Get good morning images

How to clean a kitchen sink drain

How to Cut Countertop For Sink

For cutting the countertop for your sink, you may the assistance of following tools.

So try to buy these tools from any home improvement stores or online.

Materials Required

Pen with a felt tip

Drill

Painter’s tape

Kraft Paper

Spade bit with a 1/2-inch diameter

Jigsaw

12-TPI jigsaw blades are recommended.

Two-by-four lumber is measured in length.

Screws

A belt sander, a wood rasp, or a coarse file (optional)

Knife for everyday use

Tape Measure

Step 1: Choose the Perfect Blade

While cutting laminate, there are two ways you may implement it to ensure that the corners are smooth and chip-free.

You must apply both procedures if possible.

In the first step, you will apply painter’s tape on the kitchen countertop surface, sketch the sink pattern on the tape, and then trim through it with a knife.

The second step, is to select the perfect cutting blade for the work.

Step 2: Use Jigsaw Blade with Atleast 12 TPI

Use of a commercial jigsaw blade with a limited amount of upward angled teeth is not recommended since the teeth will cut harshly and drive the laminate upward, increasing the likelihood of chipping.

Replace it with one with at least 12 TPI (tooth per inch) and with teeth that extend directly out from the shank without any upward inclination.

Another thing to consider is whether the kitchen countertop is sturdy enough—whether it is securely fastened to the cabinet or mounted on a sawhorse—so that it does not wobble or wriggle about while you are cutting.

Step 3 : Making a Mark on the Countertop for the Cutout

When you purchase a new sink, it will arrive with a pattern that you may use to create the opening in the sink.

If you’re refurbishing an old sink, on the other hand, then you just have to create your own layout.

This could be accomplished by spreading Kraft paper over the sink hole, binding down the sides, then cutting around the interior corners of the sink using a sharp utility knife to create a border.

Step 4: Give Enough Space for Positioning

In order to properly position the layout on the countertop, you must provide a minimum space of 1 1/2 inches between the front end of the sink and the front margin of the laminate countertop.

You’ll also require sufficient space at the rear for the jigsaw, which is approximately the same number as at the front.

Step 5: Measure the Size of Sink Opening

With just a measuring tape, calculate the size of the sink hole, and then use those values to draw a basic outline of the aperture on the countertop using painter’s tape.

Create an overlapping pattern on the tape by laying the template on top of it; next level the template and glue it down; then draw the borders of the tape with a felt-tip pen.

Discard the layout, and you’ll be ready to begin cutting the hole.

Step 6: Cut the Hole

A jigsaw may be used to cut the hole.

Cut a small hole within the outline using a 1/2-inch spade bit so that it barely reaches the line at the bottom.

The jigsaw blade should be slipped through the hole, the saw foot should be level on the countertop, and the cutting should start on the line.

Following the completion of almost three-quarters of the shape, you will need a bracing to avoid the cutout from collapsing suddenly and cracking the laminate backing.

A simple method for doing this is to fasten a piece of two-by-four to the cutout that is wide enough to overhang both sides.

Step 7: Dry Fit the Sink

After you’ve completed cutting and removing the cutout, you may begin dry-fitting the sink.

If somehow the sink cutout is too small, expand it using a belt sander, wood rasp, or coarse file, to make it larger as required.

Continue to enlarge the opening until the sink can be inserted easily without jamming; now take the tape off and you’re finished.

Video Guide: How to Cut a Hole For Sink in Laminate Countertop

How to Cut a Sink Opening in a Granite Countertop

Here is step by step guide to create a sink opening in a granite countertop

Step 1: Position the Granite Countertop

Install the granite on a firm work surface and secure it with clamps.

Make a mark on the cutting line.

Mask the cut line with biue or adhesive tape to reduce the amount of chip-out.

Measure again and label the tape with a new mark.

Step 2: Protect the Shoe of Saw

Make use of blue-tape to protect the shoe of your circular saw from damaging your granite countertop surface if you’re cutting with one.

The guard should not be removed if you are using a grinder. It is advised that you use face protection.

Establish a straightedge guide, similar to a shot board, to simplify the task.

The use of an angle grinder is a freehand-cutting technique.

Step 3: Don’t apply Strain

No matter what tool you select, make the tool work, but do not push the tool to move.

The chip-out will be reduced, and the cut will be as clean as possible.

If the tool is generating excessive strain, perform the cut in two stages.

Step 4: Back-Cutting Technique

Certain slab installers use a back-cutting technique.

In other respects, they leave a 2-inch kerf at the final tip of the cut so that the granite doesn’t chip or shatter severely once the cut is completed.

Step 5: Remove the Saw Marks

Take an angle grinder with sanding discs to remove saw marks from the cut edge and micro-bevel the cut edge to make it softer.

Pads range in grit from 50 to 3000 or more, based on the scale of softness and shine needed for the final product.

The procedure for cutting granite countertops for sinks seems to be the same.

A hole is drilled in every corner of the granite slab at the sink point, and plunge cuts are required to pierce the granite solid surface countertops in order to make the shift directions.

Video Guide: How to Cut a Sink Hole in Granite Countertop

How to Cut a Butcher Block Countertop

Step 1: Check the Measurements

Preliminary measurements should be taken to ensure that the width of the sink cabinet to be fitted with butcher block is accurate.

It is recommended that a 1″ overlap of butcher block be allowed at the edge of the run unless the run is free ended and also not between the opposing walls.

Step 2: Draw Line Using Pencil

The second step is to attach the butcher block to a stable platform.

Calculate the length of the cabinet run, considering the 1-inch overhang.

Create a bright line with the pencil, being sure to use the carpenter’s square to ensure that the line is exactly straight.

Step 3: Press the Masking Tape

Apply two levels of masking tape well above the pencil line you just made.

In order to ensure that your pencil line can be seen underneath the layers, keep the line strong and make it much more noticeable.

Press down the masking tape against the surface.

Step 4: Change the Position of the Blade

By using a small wing nut which lifts and descends the saw’s guide plate, you can change the level of the saw blade to the desired height.

To do this, the blade should dangle approximately a quarter inch below the surface of the butcher block countertop.

You should not use a blade that is lower and wider than the thickness of the wood because it may result in rips and fracturing of the wood countertop fibres.

Step 5: Adjust the Straight Edge Clamp

Place the straight edge grip along the line you drew using the pencil.

With the straightedge guiding your circular saw throughout the counter top, you can cut a precisely straight line across the surface.

The straightedge clamp should be adjusted such that the guide plate runs along the clamp and the saw blade runs parallel to the pencil line.

Step 6: Verify the Settings

As circular saw models vary widely, you must modify and verify the settings of both the guide plate and the blade multiple times before you are satisfied with the results.

Give yourself plenty of time to ensure that your clamp is in the proper position, since this is the most crucial stage in producing a smooth and clean cut.

Step 7: Cut along the Line

The butcher block should be cut all along the pencil line .

Circular saw movements should be consistent, but not so rapid that the blade shreds the wood counters.

Step 8: Get Some Help

Get the assistance of a friend or family member to catch the additional portion of butcher block counter top as you reach the edge of the cutting run, in order to prevent damaging or breaking up your nice piece of butcher block countertop.

Video Guide: How to Cut A Hole in Butcher Block Countertop

Conclusion

We hope this article helped you learn more about the best way to cut your countertop for a sink. We are always trying to provide new and helpful information about home improvement.

Please don’t hesitate to contact a professional plumber if you have any doubt about remodeling.

Beginner’s Guide: How to Get Rid Of Sink Smell (Updated 2022)

sink

Robert Brown

-

January 4, 2022

0

Usually, consumers don’t give much credence to their drains unless something terrible occurs. In a lot of cases, that terrible incident is either a stinky sink drain or a smelly sink drain.

Sinks, bathroom drains, and kitchen drains ought to be washed so they don’t become nasty.

Fragrances or flowers may hide unpleasant odor and drain smells, but you need to address the source to totally eradicate bad smells.

With knowledge of how to get rid of sink smell and with proper maintenance, you can avoid smelly and stinky drains.

Read the rest to understand what might cause various sink drains in your house to smell and how to remove stinky drains and prevent them from stinking.

Reasons for a Bad Odor in the Sink Drain

An accumulation of foodstuffs and debris in the drainage pipe is a common problem.

Anything except water that you drop down your sink might get stuck at the edges of the tubes or accumulate in the U-bend. In addition, germs will eventually cause it to rot and smell.

Food that has been caught in the garbage disposal unit may deteriorate if it is not removed as quickly as possible.

Indeed, the least quantity of food may produce a foul odor that arises from the sink drain.

You’re getting smells flowing up your pipelines from the sewage system.

Small leaks or dehydration, sewage gases will be capable of blowing up your pipeline when there is no moisture in your U-bend.

The answer is to look for leaks or blockages in the U-bend and repair them.

It is possible that you will need to disconnect the U-bend and wipe it in order to rectify the problem.

Hair, soapy residue, oil, and food are some of the most typical clogs that occur in sinks. Mold spores may grow in the presence of these sorts of blockages.

Mold spores may grow in the presence of these sorts of blockages.

In certain rare instances, mold may be the source of drain odor in the kitchen.

There might also be an issue with the drain pipe or the vent. This might be caused by pipe damage or a blockage in your ventilation system.

Also read

How to remove a pedestal sink

Causes of the Smelly Drain in the Bathroom Sink

There are a variety of reasons why your bathroom sink may be smelling.

Fortunately, if you have the correct equipment, cleaning a stinky drain in a bathroom sink may be a simple task.

It is essential to have a properly functioning P-trap in order to clean a bathroom sink and eradicate odors from bathroom sink drains.

A P-trap is a bent section of pipe that runs beneath your sink. Its purpose is to establish a seal in the bathroom by retaining water, preventing sewage gases from entering the room via the drain.

The P-trap in your bathroom may get clogged, allowing sewage gases to seep into the house and causing your sink to smell.

In addition, your sink should include a vent that directs any backflowing air away from the sink.

If the sewage stench coming from your sink is triggered by a clogged air vent, then you might have to call a professional for help.

If the stench is emerging from the water running from your sink rather than from the drain, it is likely that there is a problem with the faucet that is generating the odor.

Remove the aerator cap and inspect the inner surface for any accumulation or muck that might be cleaned out. The frequency with which you wash your drains has a significant impact on how nasty the stinking drain becomes.

It is also possible that there is standing water in your overflow drain, which might result in a bad smell.

Maintain the cleanliness of your bathroom sink on a regular basis, and use drainage cleaners to prevent any unpleasant drain smells.

Reasons for the Bad Smell in the Dishwasher

If your dishwasher is smelling bad, it might be because you aren’t thoroughly washing your plates before filling them.

Bits of food may accumulate in the filter and gaps of your dishwasher, resulting in an unpleasant smell that can linger for a long time.

It is essential to understand how to clean your dishwasher on a regular basis in order to prevent it from smelling.

One strategy to keep food from gathering is to use the dishwasher in the appropriate manner.

A rule of thumb is to completely remove and rinse dishes, cutlery, bowls, and other things before putting them in the dishwasher to avoid cross contamination.

Based on the problem, you may not need to wash the dinnerware with soap, but you will need to remove the debris and cleanse the dishes thoroughly.

If you don’t do this, big food pieces may get trapped between the grates. This might result in obstructions that restrict the dishwasher from emptying properly or a stinky dishwasher.

When there is food stuck in the drainage pipe of your dishwasher, it should be cleaned out.

Then, using a damp sponge, rinse the area completely clear.

You may also use a commercial drain cleaner to clear out your garbage disposal, if necessary.

It will assist in cleaning the same pipes that the dishwasher utilises and will produce a pleasant, fruity aroma.

Reasons for the Bad Smell in the Shower Drain

If your showering drain or bathtub drain is smelling, there are a handful of possible causes.
The best way to clean stinky drains is determined by the degree of the smell and the source of the drain smell.
You can have bacteria in your pipelines that are generating smells because they are feeding on waste.
During this action, a foul-smelling hydrogen sulphide gas is released, which has a distinct aroma similar to rotten eggs.
Additionally, mold can develop in warm, moist environments, and mold development on the waste that is creating a drain blockage might result in a foul odor.
Therefore, it’s essential to keep your drains clean in order to prevent foul smells and other drain troubles, such as mold.

Things to do when you notice a bad smell in the stinky sink

What to do if your kitchen sink stinks ?

Determine the source of the issue:

If the water is flowing poorly, the debris and soap scum may obstruct the pipe, generating a stoppage and the kitchen sink odor.
If the kitchen sink smell is like decaying food: then there is a chance that decomposing organic food, lipids, oils, and grease are adhering to the ends of the pipe.
If the odor is like rotting eggs, then you should check the U-bend. Because the sewer gases may leak up from the pipe owing to a fault with the U-bend.
Bathroom sink smells are readily repaired by unclogging obstructions, flushing the pipelines with a fully prepared chemical or home-made treatment, or correcting the U-bend.
Once you attempt all the ways indicated here but still smell sewage fumes, professional aid may be required.

How to Get Rid Of Sink Smell

The following is a summary of the several ways you may take to get rid of the unpleasant smell coming from your kitchen sink drain.

It is possible for food to smell bad.

Oil and fat may build up on the inside of your pipelines, catching food debris that should be rinsed away with water.

To clear out all the drains and disposal, use one of the following ways.

1. Baking soda and vinegar

Step 1: Add baking soda and vinegar

Add 1 cup of baking soda down the drain, along with the same quantity of vinegar, and allow it to rest for about 10 minutes before flushing.

Step 2: Boil a Pot of Water

When you’re resting, bring a pot of water to a boil (approximately six cups).

Step 3: Pour the Boiling Water

Put the hot water down the drain to assist with the discharge of any unwanted particles that have accumulated.

2. Citrus, Ice, and Salt Solution

Step 1: Add Ice Cubes and Salt

Pour a couple of ice cubes and a spoonful of coarse salt into the drain and turn on the garbage disposal for 15 seconds to clean it out.
The ice and salt will wipe any leftover food off the rotors and edges of the disposal, allowing it to function properly.

Step 2: Grind the Citrus Peels

After that, put a few citrus peels in the garbage disposal and powder them up to use as an odor remover.
Ensure that water is flowing through the citrus peels as they are being churned, or extra foodstuff may accumulate in your garbage disposal.
If the odor remains after your drain has been cleaned, you most likely have a plumbing problem.

3. Hot Water and Dish Soap

Step 1: Fill with Hot Water

Load the sink partly with lukewarm water and use a stopper to secure it.
This is the initial step, and it may be enough to get the job done!

Step 2: Add Dish Soap

Add some dish soap to the mixture.
To clear the drain, run the disposal and disconnect the sink.
As opposed to running the faucet, typically, the disposal will really fill up with water when this method is used.

For Sinks Without Garbage Disposal

1. Lemon and Vinegar

Note: Lemon slices with white vinegar should be frozen before being crushed in the garbage disposal.

Step 1: Slice the Lemon

Cut a lemon into tiny (1/4) slices and put them in the cup.

Step 2: Add White Vinegar

Pour refined white vinegar into the pot and leave it in the freezer for a full night.
Retrieve the crystals from the rack and drop a couple of them into the garbage disposal.
Start with a mild stream of water and then turn the button!

2. Baking soda, boiling water and essential oils

Step 1: Pour Essential Oil

When you want to feel something really, very good, then pour a few drips of your favorite essential oil into the drain after you’ve done a baking soda cleanse.

Step 2: Combine Baking Soda With Oil

In a small mixing bowl, combine roughly a half-cup of baking soda with several drops of essential oils.
Allow it to soak for an hour or two, or overnight if you want, before rinsing thoroughly with hot water. “

3. Baking soda, boiling water, salt, and vinegar

It has been suggested by several people that using coarse salt with the baking soda and vinegar combination provides almost enough additional friction to break up the grime.

1/2 cup coarse kosher salt
half a cup baking soda
1 cup distilled white vinegar

Put them down the drain in the following order.
Covering the drain will allow the bubbles to just function in the drain itself. The salt has a caustic element.
So, run a pot of boiling water through it to melt any leftover salt. There will be no more severe drain odors here either!

Methods of Cleaning the Sink Smell using Chemicals

The solutions listed below are effective for getting rid of the odor of decaying food.

Drain Cleaning using bio-enzymes

This is a biological cleanser that is both environmentally friendly and non-toxic. It functions by using enzymes that digest the food particles without causing any harm to your pipelines or other plumbing fixtures.

Commercial Drain cleaner

Many hardware shops and supermarkets provide fully prepared drain cleaning solutions, which may be purchased online.

Please look after it.

These compounds have the potential to be toxic. Please read and follow the directions stated on the container, and protect your hands and eyes with rubber gloves and glasses.

What Causes the Smell of Sewage in Your Kitchen Sink?

Sewer Odor

The piping in your home is supposed to keep dangerous sewer gas out of your home, sweep away sewage, and supply you with pure and drinkable water.
If you are really experiencing sewer smell in your kitchen, it is likely that something has went wrong with the current system.
It is not only annoying, but also has the potential to be harmful to one’s health.
Those who have impaired immune function or who have been exposed to sewer gas smell for an extended length of time can have harmful illness in their breathing organs.

Leakage

Removing the connectors on each side of the P-trap is a simple process.
Disconnect the P-trap by unscrewing the connectors on the P-trap.
Keep in mind that it might be filled with water! While you’re out there checking the pipe for leaks, make a point of thoroughly cleaning it.
If you discover a leak, take precise measurements and note them down, then purchase a new trap that is the correct size as the original.
If you are unable to locate a leak using this procedure, fix the P-trap and go to the next possible source of leakage.

P-trap

The P-trap is the curving section of the pipe beneath the sink .
It separates the water lines from the fittings, which prevents the formation of offensive odors.
The trap beneath a single fitting works by retaining water at the base of the curve, which prevents the smell from escaping.
As a result, a foul odor will emerge from the sink if the P-trap is not working properly.
If you’re using the sink on a routine basis, you can eliminate evaporation as a possible source of the odor.

Clogs

There is a little lid at the bottom point of the curve that lets you look for clogs and remove them if any are discovered throughout the process.
Remove the clog and stream the water for the next couple of seconds to refill the trap to its ideal level of filling and filtration.

Blocked Ventilation

The rooftop of every home has minimum of one primary vent that allows for ventilation.
Most regional ordinances specify that this fixture has a minimum diameter of 4 inches, and that all fittings be vented at all times.
In this manner, the gas in the piping may be ventilated, allowing the water to flow easily through the pipeline.
If the plumbing vent is blocked, it might make it difficult for the water to drain correctly.
Whereas if the sink continues to run slowly after using the strategies outlined above, it may be necessary to call the plumber for help.

How to Keep Drain Odors at Bay

The process of keeping your sink from becoming stinky is simple.

All you need are a few excellent practices and regular maintenance to keep everything running smoothly.

Take a look at the following:

Placing a drain screen above your plughole will help to prevent food chunks from entering your plumbing system.
It is best not to throw fat or oil into the drain. As an alternative, use a dish towel to mop up or wipe away any excess oil from your cookware before cleaning it.
If there is any remaining water after boiling the kettle, pour it through the plughole to destroy microorganisms.
Occasionally, sprinkle baking soda over your drain.
Periodic maintenance and inspections should be conducted.
Hiring a good plumbing service to inspect your pipelines on a regular basis can help to guarantee that they remain clean.

Video Guide: How to Remove Sink Smell

Best Guide: How to Clean Porcelain Sink (Updated 2022)

how to

Robert Brown

-

January 3, 2022

0

How to Clean Porcelain Sink: A Detailed Guide

My porcelain sink seems to discolor and scratch so quickly, which I have had for many years. Possibly due to the fact that I stuff it full of all kinds of filthy plates, but it’s possible that this is why.)

After using watered bleach for quite some time, I decided to hunt for an other cleaning solution.

I didn’t want to use such a strong agent, and it didn’t erase any of the damages, so I decided to find an alternative cleaning product.

Because my porcelain sink has two sides, I experimented with two different cleaning procedures.

But in this blog post, I had intended to share several cleaning solutions with you, Let’s see one by one!

Also read: How to remove Scratches on a stainless steel sink

Fireclay vs cast iron sink

What is a Porcelain Sink ?

Classic porcelain sinks are in trend for both domestic renovations and starter homes.
They are extremely reliable because they are produced by firing a layer of porcelain, a crystal ceramic substances, above a metal –usually cast iron.
In spite of its durability, porcelain sinks are susceptible to damage from wear and tear and everyday usage.
Porcelain sink surfaces may last a long time if they are cared for properly.

Pros and Cons of Porcelain Kitchen Sink

PROS	CONS
1. Cheap maintenance and refinishing capabilities	There are less modern styles.
2. There are several layouts and sizes available.	It is possible that home objects may be harmed.
3. Service costs are low.	It is more difficult to recycle.
4. There are many different hues to pick from.	Installation is more harder since it is heavier.
5. Use is gentle and lasts longer from 25 to 30 years.	When hit, the sink may chip or fracture.

Step by Step Guide: How to Clean Porcelain Sink

1} Using Bar Keeper’s friend

However, my white porcelain kitchen sink becomes really grimy, and I’m not kidding when I say that.

Thankfully for me, I’ve discovered an amazing method for cleansing a porcelain sink in under 10 minutes, with really no scraping necessary.

Containers and cookware are cleaned of food and hard water stains, scrapes, and scuff marks using this product!

Black scuff marks are everywhere from cookware rubbing up against the edges while preparing. In addition, the basin was completely discolored!

When I clean dishes, I usually rinse off the sink with a little liquid soap and detergent.

However those marks wouldn’t come out no matter how hard I tried. It is not only simple, but it is also quite fast to clean a porcelain sink. Allow me to demonstrate!

Materials Required

Bar keeper’s friend
brushy sponge

Step 1: Sprinkle Small Amount of Powder

Fortunately, it is simple to clean using this method! All that is required is that you wet the whole sink and then sprinkle a little amount of the Bar Keeper’s Friend powder all around the kitchen sink.

Step 2: Wet the Sponge

Fill or wet the the sponge with water and use the brushy end of the sponge to clean it out completely.
Just use some elbow grease to get rid of tenacious stains or black spots that have set up over time.

Step 3: Gently Massage the Powder

However, for majority of the “trouble” in the basin, everything you’ll want to do is gently massage the cleaning powder into the kitchen sink by using brushy edge of the sponge to remove it.
And approximately ten minutes later, the sink was restored to its former glory!
And the spots in the bowl, as well as the scuff marks around the borders, have completely disappeared!

Using Hydrogen Peroxide

Step 1: Add Baking Soda

First, fill the sink with water and run it down each side and base.
Again when the base and edges of the sink have been thoroughly wetted, block the drain and put baking soda on top.
There is no need to apply a thick coating of baking soda; a little layer would suffice.

Step 2: Use Sponge to Clean the Sink

Cleaning a porcelain bathroom sink with baking soda and a sponge is a good method.
Make use of a sponge to clean the porcelain enamel sink.
This is similar to a magical stain remover.
As I watched, the yellowish tint in the sink began to fade before my own eyes, and it was absorbed into the baking soda.
It did not need a large amount of cleansing.

Step 3: Pour Hydrogen Peroxide onto the Sponge

Now you will need to pour a minuscule amount of hydrogen peroxide onto the sponge and clean it a bit more.
The black scuff mark and stubborn stain will begin to fade, and the sink will begin to brighten as a result.
Baking soda aggregates will form in the sink as a result of this.
It’s nothing to be concerned about; this is usual.
Remove everything from the sink once it has been completely scrubbed with hydrogen peroxide.

Using Baking Soda and Lemon

Let’s see how to use baking soda and lemon to clean the porcelain sink, instead of using the abrasive cleaners.

Materials Required

Baking soda
Soft scrub brush
Soft cloth
Lemon

Step 1: Wet the Sink

Completely wet the sink and add baking soda on top of it to make it shine.
Ensure that it is completely covered with white powder.

Step 2: Scrape the Baking Soda

Using a clean cloth, scrape the baking soda into the porcelain sink till no spots are visible.

Step 3: Rub the Lemon

Chop your lemons and massage them over the inside of the sink, rubbing them in from all corners to cover the porcelain with juice.
Allow for a half-hour resting period.

Step 4: Rinse with Water

After wiping down the sink with a soft cloth, rinse it again with water and wipe it it again to ensure that it is clean.

Using White Vinegar

Materials Required

Liquid dishwashing detergent
Sponge
Soft cloth
White vinegar

Step 1: Mix Dish solution and Water

To begin, combine water and dish solution and use a sponge soaked in your that cleaning fluid to wash off the sink.
After rinsing with clean water, pat dry.

Step 2: Add Hot Water and Vinegar

Using a 3:1 ratio of hot water and white vinegar, load the sink halfway with the mixture.
Allow it to rest for 30 mins or until the filth and debris on the sink has been reduced by the solution.

Step 3: Wipe Again

Wipe the sink with the water and dishwashing liquid for a 2nd time, then rinse with lukewarm water to complete the process.
Using a paper cloth or a soft microfiber, wipe the sink thoroughly.

Using Lemon and Salt

Materials Required

Table salt
Sponge
Soft cloth
Lemon
Lemon essential oil

Step 1: Sprinkle Salt Above Stain

Gently spread table salt above the stain until it is thoroughly coated with the salt.

Step 2: Apply Lemon Juice

Slice your lemon in halves and strain the lemon juice over the salt in step two.
To avoid a discolored area, apply enough juice to coat it completely.

Step 3: Wash with Water

Wash the stain with a nylon sponge or a clean paper towel until it is completely gone.
For stubborn rust stains, just let salt and lemon combination to stay for an hour before scrubbing once more.
Then, wash well with water and wipe it away.
If you really want to give the porcelain a little shine, dab some lemon oil on it after the third and final step.
It will also provide an additional layer of protection, which is a nice benefit.

Using Dish Soap

Materials Required

Hot water
Soft cloth or sponge
Dishwashing soap

Step 1: Mix Warm Water with Dish Soap

Combine one gallon of warm water with one tablespoon of liquid dish soap.

Step 2: Clean with Lukewarm Water

The second step is to moisten a clean cloth or sponge with the detergent mixture and use it to clean the porcelain surfaces.
After it has been thoroughly cleaned, wash it well with lukewarm water.

How to take care of Porcelain Sinks

Cleaning porcelain sink on a daily basis will help to avoid the accumulation of soap scum, oil, and filth. 2 tablespoons of dish detergent to 1 gallon of water is a good ratio to use for this task.
Clean the sink‘s surface with a smooth, non-abrasive cloth or sponge to remove stains and any built-up gunk.
To remove water marks from the sink, use a dish towel or another soft cloth to brush it dry after each use.
Avoid using abrasive cleanser on your sink since they might damage it.
Oil, soap lather, and grime are drawn to the scratches, which lead to further damages.
Washing your sink with a 1:1 mixture of ammonia and a gallon of water can degrade them and restore the lustre to your sink.
An efficient way to eliminate oil and soapy slime build-up is to use a concentration of 1 tablespoon trisodium phosphate to 1 gallon of water.
As well as being known as TSP, trisodium phosphate (a disinfecting chemical) may be purchased in white dry powder at most household shops.
Make a thorough cleaning of your sink. Fill the base of the sink using paper towels and fill the rest of the sink with concentrated bleach.
Ensure the space is adequately maintained, and allow the bleach-soaked towels to rest for 15 to 30 minutes before removing them.
Wash the surface off completely with water and then, use a wash cloth or another soft microfiber to wipe them.
A mixture produced from a mug of borax combined with a quarter-cup lemon juice may be used to remove rust spots.
Scrub the mixture into the dirt with a fresh, smooth cloth or sponge, and then wipe well with lukewarm water.
Large things should be placed into the sink with caution. It’s best not to throw them.
Allowing heated cookware to cool before putting them in the white porcelain sink is recommended.

Video Guide: How to Clean Porcelain Sink

Wrap Up!

Polishing porcelain kitchen sinks may be an option once you’ve removed stains and scratches.

In the end, your ceramic sink or tub will remain cleaner, tougher, and less susceptible to marks and spots with a high-quality finish.

You can do it alone with some inexpensive store-bought supplies, but you have the option of hiring a professional if you prefer.

Do not hesitate to share these ideas and tactics on how to clean porcelain kitchen sink on Facebook or Pinterest with your friends so they can get the benefits as well!

FAQ

What is the best cleaner for porcelain?

Bona Hard Surface Floor Cleaner is the best cleaner for porcelain

A pH-balanced cleaner, such as Bona Hard Surface Floor Cleaner, can protect your coated or uncoated porcelain flooring neat and tidy for years to come.

How do you get stains out of a white sink?

Pour a couple of Tablespoons of Bar Keeper’s Friend powder into either side of the sink and mix well. Combine some white vinegar to form a paste out of the ingredients. Scrape the sink with this combination and then rinse it off. Use a small bit of bleach to clean the complete sink, then rapidly rinse it off with water.

Does baking soda clean porcelain?

Baking soda, like vinegar, is among your finest partners when it comes to making your own porcelain cleanser at home. Baking soda contains chemical cleansing capabilities as well as being a mild abrasive, making it the perfect solution for washing your porcelain bathroom sink.

Does baking soda damage porcelain?

The use of baking soda, borax, and even salt, while often regarded as softer choices to harmful chemical cleaners, may cause permanent damage to the surface of your porcelain fixtures. Despite their benign nature, these substances are nevertheless abrasive and will harm your surface over time, particularly if used on a frequent basis.

Is Bar Keepers Friend safe for porcelain sink?

Yes, it’s safe for most surfaces, even porcelain, but it’s always a good idea to try Bar Keepers Friend Cleanser out on an isolated area of the tubs and fittings initially.

Best Guide: How to Remove Scratches From Stainless Steel Sink ( Updated 2022)

sink

Robert Brown

-

January 2, 2022

0

Are you tired of seeing scratches on your stainless steel sinks ? Don’t know how to remove scratches on stainless steel sinks?

Then, read this blog post to get a clear-cut idea of the full procedure. I explained it in a detailed manner.

Generally, you will have to use a scratch removal compound, like Bar Keeper’s Friend, in order to remove scratches from your stainless steel sink. Then, rub a microfiber cloth gently over the scratch with a small amount of the compound. Afterward, wipe the surface with a clean cloth. Keep repeating the process until the scratches are removed.

Kitchen appliances can be made of stainless steel, which is one of the finest materials to use in the kitchen. It is sturdy and sleek and is available in a variety of finishes.

The amazing benefits of this material make it well suited for use in home appliances, sinks, and counter tops as well.

However, it may be damaged easily due to certain factors.

Scratches or other forms of damage may occur easily. Usually, scratched surfaces will have a dull appearance. A kitchen with scratched surfaces will appear dated and unappealing.

In addition, you should know that, it is always possible to replace the damaged stainless steel product with a new one.

However, this would be a pretty costly decision on your part.

Luckily, it’s not difficult to fix scratches. This blog post will explain how to remove scratches from stainless steel sinks with a minimal amount of effort.

Also read: How to Caulk a Stainless Steel Sink

How to remove chemical stains from stainless steel sink

How to clean a kitchen sink drain

How the Stainless Steel Sinks are Manufactured ?

The first thing you should realize is that stainless steel isn’t a natural metal. It is actually a mixture containing various metals and alloys that are typical of each type.

To begin with, a bit of scrap steel is melted. Steel scrap is usually composed of reusable steel.

Nickel or chromium is then used to mix with the melted alloy. After that, they are processed to provide stainless steel with its essential properties.

The resulting material will resist corrosive effects as well as heat. In addition to this, it can also be recycled and made into the desired product with ease.

How Does a Stainless Steel Sink Get Scratched ?

There is no doubt that stainless steel is the most attractive material available for kitchen sinks.

The downside is that it is also very prone to scratching. This is because a stainless steel sink can be damaged in many different ways.

First, stainless steel is easily worn down by ordinary daily use since it is so prone to scratches.

Even something as simple as putting and taking away dishes and utensils from the sink can cause scratches on stainless steel. In some cases, this cannot be avoided.

It is recommended to avoid using wire sponges and harsh metal brushes on your sink, as using them continuously can result in noticeable scratches.

Also, certain cleaning products may affect stainless steel sinks.

There are some materials that are considered abrasive to stainless steel sinks. This includes steel wool, scrub pads, and bleach.

If you have ever used them on your sink, you might have noticed that your sink is getting scratched quite frequently and also getting dull.

How to Remove Scratches From Stainless Steel Sink

If you have a stainless steel sink that has scratches, there is absolutely no need to worry. You can easily remove that using these methods.

Materials Required

In order to achieve this, you will need to collect a few pieces of material first. Among them are:

Two microfiber cloths
Stainless steel scratch removal kit
Stainless steel scratch removal compounds such as Bar Keeper’s Friend
Water

As soon as you have these items, you can begin to work on scratch removal.

However, it is imperative to note that the following guides are intended to treat normal scratching, not very deep scratches. We will provide instructions for deeper scratches separately.

Step 1: Add Water to Powdered Stainless Steel Scratch Removal Compound

Now, take the powdered stainless steel scratch removal compound and combine it with water.
Start with a few drops of water, then add more and more.
A paste with a texture close to toothpaste should be produced as a result of this process.

Step 2: Dab Microfiber Cloth

Take one of your microfiber cloths and dab a bit of the removal compound on it.
Scratches should be treated softly by rubbing the mixture on the cloth back and forth over them.
Again, for ideal results, you’ll want to press along the path of the metal’s grain as much as possible.
Repeat this until the scratch has been removed.

Step 3: Gently Clean the Surface

To remove any remaining residue, softly clean the area with the second microfiber towel.
The towel should be clean and somewhat moist.
It’s also a smart idea to dry the area with a third microfiber towel.
However, leaving the area to dry naturally is also acceptable.
If necessary, repeat the process several times to ensure that no more scratches are left.

How to Remove Scratches From a Stainless Steel Sink Using Olive Oil

When it comes to scratch removal, oil is always a wonderful substance to consider.

It is useful if you want to get rid of minor imperfections in the smallest of details.

A minimal drop of olive oil should be applied to a washcloth or a paper towel.
Rub the lubricated cloth on the scratches in a back and forth motion.
Try to see whether you’ve made any progress by wiping down the area.
You should keep repeating this technique until you achieve the desired outcome.

Best Methods to Remove Deep Scratches

In certain cases, deep stainless steel scratches need to be addressed using a standard scratch removal solution.

If you have a scrape like this on your stainless steel surface, you’ll want to invest in a stainless steel scratch removal kit.

The advantage among these sets is that they come with both a sanding compound and a pair of abrasive pads, which is really convenient.

These are especially designed to be favorable to stainless steel items rather than detrimental to them.

Detailed instructions on how to make use of one of these kits are provided below:

Step 1: Determine the Sink’s Grain Direction

Begin by looking through the owner’s manual one more time.
It is also necessary to determine the grain direction of your stainless steel sink prior to beginning the setup process.

Step 2: Select the Right Grit Pad

Choose the right grit pad and massage it against the scratch in a circular motion.
This should be carried out along the sink’s grain direction. Furthermore, just move it in one direction at a time, rather than back and forth.
It is possible that new imperfections will arise as a result of this action.

Step 3: Wipe the Area

Lastly, just apply the amount of pressure necessary. Don’t press yourself too hard when you’re working.
In certain cases, a softer grid pad may be requested by the manufacturer.
Keep going with the polishing procedure that you started in step two.
During this stage of the procedure, you may also be instructed to put a little water on the pad.
After that, wipe the area using a microfiber cloth that has not been used before.
This will help polish the surface of your sink to a bright sheen.

Remove Deep Scratches from Stainless Steel Sink Using Sandpaper

Deep scratches, as opposed to small scratches, are a bit more difficult to eliminate. For these sorts of marks to go, you’ll have to invest in some more work and time.

Various items will be required for this sandpaper removal process to be successful. Warm water and two different kinds of sandpaper will be required initially.

One must be 1000 grit sandpaper
other will be 600 grit sandpaper, respectively.

Step 1: Join Grit Sandpaper to Sanding Block

You must first connect the 1000 grit sandpaper to a rubber sanding block before you can begin polishing.
After that, feed a small container halfway with warm water.
Place the block of wood into the storage container.
Allow the sandpaper to remain in the water for a few minutes.

Step 2: Apply Equal Pressure

After that, pick up the wet sandpaper and massage it over the affected region with some pressure.
Ensure you’re applying constant pressure to both sides of the sandpaper sheet.
It’s also easy to wrap sandpaper around a block of wood.
You’ll be able to spread the pressure more uniformly this way.

Step 3: Clean the Surface

It’s also important to remember to re-wet the sandpaper after each use.
Once you’ve done that, clean the area where you’ve been rubbing to check whether the scratch has faded.

Remove Severe Scratches using Scratch Removal Kit

Scratch removal kits, are available at most local hardware shops. Certain sinks are provided with specific manufacturer’s recommendations for preventing scratches. \

Using these guidelines, you will learn how to remove scratches from a stainless steel sink and whether or not purchasing a scratch remover will be effective for the sink in question.

Step 1: Mix the Removal Powder with Water

If you already have the option of using a remover, go for non-abrasive cleansers.
Stainless steel and copper cleaners are excellent for removing severe scratches.
They are all powders in one form or another.
You must mix them with water or other fluid cleansers to get the best results.
In this manner, the powder will glide more smoothly on the metal.

Step 2: Apply Correct Quantity of Powder to Pad

The grit pads that are included with all of the removal solutions are quite useful.
Pay close attention to the directions.
Apply the prescribed quantity to the pad that is already in place.
Alternatively, you may apply the scratch remover straight onto the scratch.
Then, begin to move in the suggested directions.

Step 3: Use Lighter Sandpaper Grit to Remove Minor Scratches

Once you’ve rubbed off the majority of the scratch, move to a finer sandpaper grain to finish the job.
It may be used to scrub away the last minor scratches.

Step 4: Wipe Away the Surface

After you’ve completed all of these steps, it’s time to clean using a microfiber cloth.
To remove any remaining surplus, wipe it away with this towel.
Clean the area down with a clean cloth.
You may also wipe it with water if you like.

It may be rather horrible to look at your sink if it is scratched or discolored.

Because of this, you should get rid of them as quickly as feasible.

The techniques outlined above are an excellent set of guidelines on how to remove scratches from a stainless steel sink and may be followed.

Whatever technique or product you choose to remove scratches, it is critical that you just scrape in the direction of the grain. If you don’t take the appropriate steps, you may end up worsening the situation.

Adopt and adhere to the procedures that are suited for the sort of damage you have. If you don’t feel secure in your own sink, consult with a professional.

Professional stainless steel archivists will visit your house to assess the damage and provide you with an estimate for the repairs needed.

How to Clean Stainless Steel Sinks

Another suggestion is to create a cleaning schedule for your stainless steel sink that will not cause harm to the surface of the sink.

In particular, this is critical since most of the damages that stainless steel sinks sustain are the result of insufficient cleaning procedures.

An easy daily treatment, combined with a thorough weekly washing with a mild abrasive cleanser, is recommended by the professionals.

Bar Keepers’ Friend is one of the excellent choices in this situation.
Keep in mind that you must always scrub in the path of the polished lines on the inside of your sink while you’re cleaning.
This will guarantee that you aren’t really skimming the surface that you are attempting to make seem more attractive.
Apart from that, chlorides are included in the majority of household cleaning products, which may cause deterioration in stainless steel.
Be careful when you’re using detergents that include chlorides during your routine cleaning.
Ensure to wash them off from the surface of your sink as fast as possible after use.
Furthermore, whenever cleaning, avoid using carbon steel brushes or steel wool to avoid damaging the surface.
It’s almost as if using these household items is a guarantee that additional scratches will develop in your sink.

How to Polish a Stainless Steel Sink

In order to make your sink stand out even more, you may choose a variety of different materials.

For example, club soda is a fantastic choice for this.

All you have to do is spread a little amount on a soft cloth and massage it over your sink.

Make sure to rinse thoroughly when you’re done to avoid water marks from appearing.

A result identical to this may be achieved with baking soda and a vinegar wash.

Despite the fact that baking soda is harsh, it will not harm your sink if used to remove hard-water residues and trapped grease from it.

When you add vinegar to your sink, it will bubble and fizz, even while cleansing the sink.

Another alternative is to use olive oil to polish your stainless steel sink, which will make it gleam.

The shine that you want may be achieved with only a few drops of oil applied to a clean, lint-free towel.

Stainless steel may be scratched, so what can you do to prevent this?

Certain scratches on your stainless steel sink might be tough to remove using a polishing cloth.

To avoid scars in the first place, it’s important to educate yourself on what you should do to prevent them from forming in the first place.

Fortunately, there are a few steps you can really take right now to guarantee that you will never have to cope with as many scrapes in the future as you would otherwise.

First and foremost, it is advisable to get a sink guard. These are the ones that sit at the base of your sink and enable water to pass through.

Although they do not provide complete protection, they do give sufficient protection to keep your stainless steel sink from being damaged by plates and cutlery.

It’s also critical that you cleanse your sink using the proper supplies and methods.

It is recommended that you only use non-abrasive products, such as Bar Keeper’s Friend, Soft Scrub, and other similar products. This will ensure that the natural surface of your sink is maintained.

How to Maintain Stainless Steel Sinks : Video

Conclusion

Scratches in stainless steel sinks are a very common problem for many homeowners. Not only are they unsightly, but they also can make your sink look dirty even when it is spotless.

Fortunately, there are several ways you can remove scratches from stainless steel. We hope this blog post has helped you to solve the problem of scratched sinks in your own home.

If you have any other questions or concerns, please contact us. Thank you again for reading, we are always excited to share our knowledge with our readers!

How to remove a pedestal sink

Step 1: Shut off the water supply

Switch off the water supply to your pedestal sink prior to starting to remove it.
For further precaution, you may want to switch off the building’s main water supply.
If you want to keep your older faucet on a new sink, be sure the new sink has the correct pipeline and space.

Step 2: Disconnect the water supply Lines

Lay blankets on the ground beneath the water supply lines.
Remove the water supply lines on both sides. Even though the water supply has been cut off, there will be some standing water in the pipes that will drain once you unplug them.
Standing water will be trapped in the drain and supply pipes by the towels.

Step 3: Unplug the P-Trap

Remove the P-Trap from the wall and detach it.
The P-trap is a fixture that stops unpleasant air or gases from leaking back into your home from your drainage lines.
Again, for the time being, keep the faucet and drain lines connected.
As soon as the pedestal is taken, it will be much easier to detach them from the wall.

Step 4: Remove the Sink

Ensure that every connection to the sink has been safely disconnected.
Ensure the P-trap is completely moved from the wall, whereas the sink is also removed with the support of a partner.
If any fastening bolts are present, be careful to remove them.
If you want to reuse them in a fresh installation, then keep them.

Step 5: Separate the P-trap

The P-trap on the pedestal sink can now be removed.
If you really want to retain any of those components on the new setup, you can wash out the pipelines and P-trap prior to actually joining them to a new sink for placement.
Tip: The edges of a broken sink may be extremely sharp.
To safeguard yourself, always use safety gloves while handling a broken pedestal sink.

Step 6: Disconnect the hardware

Many cities have their own sets of laws and restrictions for disposing of things like porcelain and metal.
To fulfill any disposal regulations, it’s a great idea to remove any metal components from your former pedestal sink.
Furthermore, if you intend to reuse the gear on a new installation, detach it as soon as the sink is unplugged so you may inspect it and determine whether it is suitable for a new installation.
If this is the case, the supply lines and faucets could be soaked and washed to restore their look before being reinstalled.
You may not be able to extract hardware using a wrench in several cases, especially when changing much older pedestal sinks, and will have to slice through with a chainsaw to release the sink.
Supply lines should always be terminated as near to the sink as feasible.

Congrats! Now you’ve finished the job of removing the pedestal sink. If this is your only motive, then you can skip further reading.

But if your motive is to remove the pedestal sink and replace it with a vanity, then keep on reading! I will explain the steps you need to follow.

Video: How to Remove A Pedestal Sink

https://www.youtube.com/watch?v=a4DkcY845w0

How to Remove a Pedestal Sink and Replace it with a Vanity

Upon the removal of the pedestal sink, you will need the following materials to replace the sink with a vanity.

Materials required

Screws
A Level
A Marker
Tape Measure
A Stud Finder
A Drill
Saw (Optional)
wall anchors (optional)
shims (optional)
a utility knife (optional)

Step 1: Select the best location

The first step is to find the best area for installing your bathroom vanity.
Take your marker and tape to measure the space that your bathroom vanity is going to fill up.
You can also refer to the manual provided with your vanity to make accurate measurements.
Next, take the stud finder and aim to align your bathroom vanity with the load-bearing unit.
After you’ve discovered the correct stud, make a note of it using your highlighter or marker.

Step 2: Drill Holes in the Pipes (Optional)

Verify whether your bathroom vanity has an open back or not.
Incase it doesn’t have one , then you’ll have to drill holes in it with a saw to make openings for the pipelines.
Check your pipelines first to determine the size of the openings.
Create holes that are somewhat larger than the size you chose.
It is critical to make the holes slightly larger so that the pipes have ample room to stretch and wander over.

Step 3: Install the Bathroom Vanity

Before relocating the bathroom vanity, disconnect the doors, cupboards, and other chambers.
They may get in your path and cause harm, so eliminate them for the time being.
Set the bathroom vanity in its specified location, making sure it aligns with your dimensions.
Use a level to check the alignment of the bathroom vanity.
If somehow the vanity is too small, you may alter the feet until it comes to the correct height.
Certain vanities do not have adjustable feet, so you will need to use shims to correctly place them.
Again, when the shims are in position, trim away any extra material to bring the vanity into optimal alignment.

Step 4: Drill the Bathroom Vanity

Then, take your drill and drill via both the vanity and the bathroom wall till you reach a stud.

Reason for Removing a Pedestal Sink

There might be a variety of reasons why you want to get rid of your pedestal sink. The following are some of the most typical reasons for removing your pedestal sink.

Maintenance

Your pedestal sink may require repair every now and then.
This might be due to physical damage or a technical fault.
If your pedestal sink is giving you issues, you may have to remove it to identify the issue.
If you have appointed an expert to handle your sink, they may need to remove the sink.
Servicing your pedestal sink will result in better durability for your sink.
It may also lead to increased efficiency.

Cracked

Even if we never want this to occur, it is sometimes unavoidable.
If your pedestal sink is broken, you will almost certainly have to replace it.
If you wish to replace or fix it, you may need to do this.
Removal of pedestal sink allows you to reach the defective sections of the sink.
You can also get to the water lines if the fault is there.
You’ll need to remove the sink to replace the majority of the broken pieces.

Replacing

It’s possible that your sink isn’t broken, but that you’ve opted to end things with it.
You’ll have to disassemble your pedestal sink if you wish to replace it.
This might be due to an improvement, repair, or simply a new design.
Nevertheless, if you want to be successful in replacing it, you must first remove it.
Changing your pedestal sink should be considered as a possibility.
You may choose a design that complements your area while still providing the efficiency you want.

Shifting

Relocating to a new place is another reason you might wish to remove your pedestal link.
This is rather frequent, particularly if you want to perform any renovation.
If you’re rearranging your living room, you’ll want to transfer your pedestal sink.
If that is the case, it becomes even more critical that you understand everything there is to learn about relocating your sink.
You might ruin your pedestal sink if you don’t know what you’re doing.
Whenever you relocate your pedestal sink, make sure you understand what you’re doing.

How to remove a pedestal sink glued to the wall

Removing a pedestal sink is usually rather simple. But if someone has applied construction glue or adhesive caulking to keep it from sliding, then the process will become difficult.

This is one of those situations when you pray for the best but prepare for the worst.

A pedestal sink is supported by a base. There are a few holes below the sink that permit the installer to connect screws into the drywall.

Almost all of the time, the sink is secured to the walls at these points and then caulked around the circumference.

If glue is applied, it is hard to separate the sink without harming the walls. So prepare for it. You may try cutting through the glue around the circumference with a large blade.

During that process, you will notice that the glue is quite tricky to slice through.

When you’re fortunate enough to be able to slice through this one, slice the base first, then the head while supporting the load of the sink.

You don’t want the sink to tear the sheet away from the walls and scrape away the grain. However, if you are willing to cut through the glue, a strong band of adhesive will remain adhered to the walls.

You can peel some of it off the wall with a sharp putty knife, but you’ll have to fix the drywall or use a bigger sink to hide the damage. In rare circumstances, I have broken it apart by hitting it against the wall.

I don’t suggest it, but it could be necessary as a final option.

Ready for certain wall work irrespective of how the sink is removed from the wall.

Video: How to remove a half pedestal sink

Conclusion

Removing a pedestal sink is not too difficult a job to undertake, but it’s certainly a bit different than removing a sink that is already installed in a countertop.

As we mentioned, you will need to be careful when removing the sink from the countertop, but with a pedestal sink, you also have to be careful when removing it from the cabinet, as there are often pipes and wiring connected to the pedestal.

Step by Step Guide: How to Install Kitchen Sink Drain ( 11 Best Steps)

how to

Robert Brown

-

December 28, 2021

0

It’s a step-by-step method to install your sink. In this post, we’ll talk about how to install kitchen sink drain.

Everybody with basic plumbing experience must be able to complete this task very quickly.

When you’ve never worked on your own drain pipes before, I’d recommend starting with a simple repair like changing the faucet or internal workings of your bathroom.

Setting up a new basket strainer to fix a rusted and leaky kitchen sink drain is a simple fix. Begin by putting plumber’s putty on the basket strainer’s backside and inserting it into the drain opening at the base of the sink. Next, using a basket wrench, adjust the nut to keep it stable. After that, attach a brass tailpiece to the basket strainer’s base, then rejoin the drainpipes, and so you’re finished with the job!

Also read

How to Install Kitchen Sink Drain

Step 1: Select the Drain Assembly Kit

A drain assembly set will comprise a basket strainer, locking nut, rubber washer, friction ring, and brass tailpiece to join the drain to the drainpipes.
Ensure you have everything you’ll need to setup your drain, and also ensure that it slips into the drain opening at the base of your sink.
Keep in mind that the basket strainer you chose should match the drain hole.
In case your sink already has a basket strainer, use that as a guide when shopping for a new one to ensure it will match.
Ensure the tailpiece matches your drainpipes, and pick a brass tailpiece to ensure the longevity of your drainpipes.
Sink drain installation kits are available at local plumbing stores, super markets, and Amazon.

Step 2: Detach the Drainpipe

Rotate the brass connectors on the drainpipe using pliers, next detach it from the tailpiece on the drain’s bottom.
Now, using a basket wrench, remove the bolt on the base of the basket strainer and take the strainer out from the drain opening at the base of the sink.
If you’re inserting a sink drain onto an existing sink with drainpipes connected, you must first remove them while mounting the drain.
While separating the pipes, be cautious not to harm them with the pliers.

Step 3: Apply Plumber’s Putty

Add a decent bit of plumber’s putty out of the package and rub it for a moment, or perhaps once in your hands to heat it up and make it more malleable.
Finally, using your palms, wrap the putty into a cylindrical thread approximately 4–5 inches long.
Enclose the thread around the base of the basket strainer to determine how long it should be.
Make a putty rope with a uniform diameter.
Plumber’s putty is available at home improvement stores, retail stores, and online at Amazon.

Step 4: Add Putty to the bottom of the basket’s lip

Turn the basket strainer inverted and push the plumber’s putty into the bottom of the lip with your fingertips.
Apply the plumber’s putty all around the whole basket strainer and push it down.
Don’t push the putty too tight so that the thread is stretched too slim and the putty slips over the basket’s edge.
If the putty string is too lengthy, just cut it off and link the two sides of the putty.

Step 5: Position the Basket Strainer

Position the basket strainer above the drain hole and carefully press it into position so that it’s uniform and the strainer’s mouth is level with the drain hole’s tip.
Once you push down, the plumber’s putty will stretch into the gap between both the strainer’s edge and the drain hole, forming a hermetic seal.
To make an even seal, press vertically down.
This is because, the putty will harden and produce a washer, don’t give it more force because it will push out from the basket strainer’s corners.

Step 6: Clean Excess Putty

After some time, the plumber’s putty will be stretched, and extra putty may be dripping or collecting at the basket’s base.
Wash away any extra putty using a clean cloth to ensure a clean and uniform seal.
When you’re operating on a pre-installed sink, unlock the cabinet doors and gain access to the area under the sink.
Extra putty is acceptable, but if there is too much spilling out of the edges of the basket strainer, it might weaken the bond.

Step 7: Position the Rubber Washer

Insert the thick rubber washer above the basket strainer’s base.
Next, move the thinner, white friction ring above the bottom, pressing it against the rubber washer.
Now, with one hand, hold the two parts together.
Place the rubber washer on the first part to establish an extra layer of hermetic seal, followed by the white friction ring to shield the rubber washer from the bolt.

Step 8: Tighten the Nut

Grab the nut that looks like a big metal ring and align the threads with the threads on the base of the strainer.
Tighten the nut by turning it clockwise or right.
Continue twisting until it is as tight as possible.
Turn the nut as far as it will go by hand.
To maintain the basket strainer steady, grab a set of needle-nose pliers and grasp the slits in the strainer’s base.
Place a basket wrench above the nut and tighten it as much as you can.
To ensure the basket strainer is tightly secured and water does not seep out of the drain, screw the nut using a wrench.

Step 9: Place a Compression Gasket

With your fingertips, take off the plumber’s putty that has been squeezed in between the basket strainer and the drain opening.
Scrape any extra putty from the drain so that it appears clean and uniform, and the seal is waterproof.
When you secure the nut with the wrench, a small amount of putty will be pushed out.
Next, you should align and match the connections on the brass tailpiece with the holes on the basket strainer’s base.
Using your arms, tighten the tailpiece as much as possible.
A rubber compression gasket is a tiny, pliable seal that keeps water out.
In the head of the sink’s drainpipe, place a compression gasket.
It should be tightly secured in place.
Rubber gaskets are available in a wide range of sizes.
Pick one that has the right size for your drain pipe’s length.

Step 10: Align the Connector

The drainpipe you unplugged will be right under the sink drain’s brass tailpiece.
Adjust the two sides of the drainpipe so that it touches the base of the brass tailpiece.
If you strain or give more force on the drainpipe, it may crack.
A little plastic rings placed onto the tailpiece is attached to the drainpipe.
Adjust the studs at the base of the brass tailpiece with the holes at the top of the drainpipe.
Secure the connector to the brass tailpiece.
Align the connector you fitted onto the brass tailpiece using an adjustable wrench.
Secure the connector with the wrench so that the drainpipe is attached to the tailpiece and secured.
If the connection is overtightened, the plastic may break.

Step 11: Check for Spills

After switching on the water, check to see if water is coming through the basket strainer and then into the drain pipes.
Ensure there isn’t any water spilling out below the sink and ensure that the drain is functioning effectively.

Video Guide: How to Replace Kitchen Sink Drain

How to Install Double Kitchen Sink Plumbing

Since you’re not a skilled plumber, kitchen sink plumbing, just like every other plumbing installation, it could be difficult.

However, you might not be too anxious. You will be Ok as soon as you have somewhat simple plumbing skills.

Even-though a few double kitchen sinks have unique p-traps for each bowl, the majority of them are intended to function with a single trap that links to the drain pipe.

The most popular method for installing a double sink drain is to link the two sinks with a straight drain arm that is joined to the p-trap through a sanitary tee fitting.

If one of the sinks has a garbage disposal, installing double kitchen sink plumbing is little more difficult. However, if done correctly, your sink will last for many years.

Many disposals can be converted to work with a two-bowl design.

Step 1.Turn off the water valve

If the pipelines are switched on, you won’t be able to accomplish anything.
The valves normally located under the sink should be turned off.
If you can’t locate them, switch off your building’s primary water supply connection.

Step 2. Attach the drain assembly

Then, the drain assembly must be installed.
The flange and stopper, the main section below the sink, and the ball-and-rod mechanism that assists in controlling the stopper’s motion will comprise the drain assembly.
Mount the drain assembly in the wall aperture at the base of one of the sinks prior to installing the sink in the cabinet.
The garbage disposal system should then be installed in the second wall slot, and the process should be repeated.
Use a bunch of plumber’s putty to make sure every hole is completely sealed.
To turn the screws, you need to use an adjustable plier.

Step 3. Mount the Sink

Now, mount the sink to the cabinet.
Each sink is equipped with clamps that hold it to the cabinetry.
Using a screwdriver, screw the clamps into the cabinetry.

Step 4. Connect the Garbage Disposal

Install the garbage disposal in the container properly.
This is, in my opinion, one of the most practical aspects of the setup, and you should consult the manufacturer’s handbook for detailed instructions.
The usual procedure entails locking the disposal unit in position by spinning it counterclockwise.

Step 5. Connect the Tail Piece

Next, you’ll have to operate on the tail portion of the sink alone without the disposal unit at this stage.
A slip screw should be used to attach the tail piece to the slotted drain port.
A slip screw is a flexible threaded band that can be easily attached by hand.
However, you may use channel-type pliers to connect it, but you’ll have to be very careful.

Step 6. Join the sanitary tee and the tailpiece

Thereafter, use a plastic compression nut to attach the sanitary tee to the tailpiece.
Hand-tightening of the compression nut is possible.
A compression washer can also be used to verify that the tailpiece is securely attached to the sanitary tee.
With a tape, measure the length between the tee connector and the garbage disposal system outlet.
Next, using a hacksaw, take a small part of pipe to link the disposal system and the tee from that length.
Compression nuts and washers should be used on both ends to provide an airtight seal.

Step 7. Set up the P-Trap

Next, slide the p-trap unit into the tee’s bottom tip.
The p-trap should then be connected to the drain opening on the sidewall.
To avoid spills, you should additionally coil an adaptor around the p-trap.

How to Install Kitchen Sink Drain With Silicone

Certain silicone caulk tubes may be squeezed out by hand, while other silicones require the use of a caulking gun.

When you first get it out of the package, silicone caulk will look like a transparent, flexible liquid. The caulk starts to develop a skin after roughly an hour of contact with the air.

When the silicone caulk dries, it hardens but not to the point of brittleness. Silicone caulk isn’t a common option for sealing a sink drain since it doesn’t become watertight until it’s completely healed.

If you ever decide to use caulk, make sure it’s 100 percent silicone, not other materials like acrylic, latex, polyblend, or sanded types, which aren’t designed to be exposed to water.

Silicone caulk, like plumber’s putty, isn’t permanent and must be replaced at some point.

Use silicone caulk to add a more even layer of silicone caulk to the bottom of the sink’s drain system and to the sink directly surrounding the drain hole aperture.
Excess silicone caulk can leak out from behind the drain bowl and the sink, which you must clean off before it solidifies, just like plumber’s putty.
To loosen solidified silicone caulk, go to a grocery or home maintenance store and buy a caulk softening solution.

Video Guide: How to Install Sink Drain Pipe

Conclusion

The kitchen sink is the most used room in your house, therefore, it is important that you have both a kitchen sink and a bathroom sink.

If your current sink drain is in need of replacement, it is important that you take the time to plan out how you will replace it.

By sitting down and planning out how you will install your kitchen sink drain, you will be able to do the job quickly and easily.

If you are unsure of how to install kitchen sink sink drain, follow the above steps to ensure that you get the job done in a timely fashion.

Step by Step Guide : How to Remove Sink Drain (10 Best Steps)

how to

Robert Brown

-

December 26, 2021

0

In the future, if you plan on renovating your bathroom or kitchen, you may want to consider adding a new sink to the mix.

It is necessary to remove the sink drain and remove the plumbing before you can use your new sink. But, many people don’t know how to remove sink drain.

It might sound like a difficult task to replace a sink drain, faucets, and sink, but it’s much simpler than you might expect. Find out how to remove the sink drain with this comprehensive guide.

Must Read

Things to Consider before removing the sink drain

The installation of new pop-up sink drains, sink, and faucets in your bathroom or kitchen is a quick and easy way to update your space.

In order to remove the sink drain, you will need to detach everything it is connected to, including the pop-up sink drain and the P-trap.

Make sure you watch out for sink installation issues and plumbing problems.

Remove caulk:

Caulk is the only thing that keeps your countertop from getting water damage.
In order to ensure the bond is watertight and long-lasting, you must completely remove the old caulk.
Once the old sink is removed, use a putty knife to remove the plumber’s putty or caulk.
When removing stubborn caulk, it is advisable to use a caulk remover.
Leave it for a few hours and then take it off.
Caulk is used to hold these sinks in place.
The caulk will need to be cut through if you wish to keep your laminate countertop when replacing your sink.
You will need a sturdy putty knife and a strong utility knife for this task, as well as a great deal of patience.

Be cautious of swelling countertops:

Inspect your sink’s rim for leaks and stains caused by water.
It is possible for your particleboard to absorb moisture from the plastic laminate.
Your new sink installation won’t be impacted by minor water damage.
If indeed the swelling is excessive The sink would not sit level on the counter, and a collapsing ground will leave sink screws less stable.
If you find any of these flaws, the countertop must be changed.

Throw away your older pieces:

It’s critical to suppress the urge to save money by recycling outdated and aged drainpipes.
The likelihood is that they will not make a strong connection.
The reality is that replacing your sink drain is significantly easier and much less liable to cause a break.

Remove the sediment:

When dealing with water pipes, it is normal to blow debris away.
Clogging your new pop-up sink drain is the final step you want to do.
To solve this situation, clean the water systems before connecting to your fresh supply lines.

How to remove sink drain

To install a new drain for your kitchen sink, follow these steps to remove the cracked drain and replace it with one that will allow your bowl to be used for more important tasks.

Materials required

A kitchen sink drain kit
Plumber’s putty
A basket or wrench
A pair of pliers
penetrating oil

Steps on how to remove sink drain

Step 1: Switch off the water supply

Switch off the hot and cold water connection to the bathroom sink faucet by searching for the shut-off knobs in the sink cabinets.
This process may not be essential since the area of the sink you will be dealing on does not have anything to do with the water system pipes.
Switching off the shut-off valves, on the other hand, is something that a new plumber should become accustomed to.
This measure will guarantee that you do not spoil your work even if you accidentally switch on the water faucet, which is especially important if you have placed a touch – free sink faucet.

Step 2: Disconnect the Drainpipes

The P-trap and the tailpiece from the sink drain are held connected by a connection ring.
Connect a wrench to this connection and remove it by rotating the wrench counterclockwise.
After loosening the connector’s strong hold with the wrench, you may use your hand to release it from the tailpiece more easily.
Certain tailpieces feature threads that match the ones on the sink drain strainer.
The tailpiece can be removed by unscrewing it from the base of the drain strainer by twisting it anticlockwise.

step 3: Remove the Sink Drain Nut

A locking nut, sometimes termed as a basket nut, can be used to properly fasten the kitchen sink strainer underneath the sink.
The sink drain should not leak if this screw is firm enough and the sealing components, such as plumber’s putty and rubber washers, are in excellent condition.
Therefore, when your sink drain is overflowing, it might be due to a failure of some of the sealing parts, or it may be due to the lock nut not being secure sufficient.

Step 4:Apply Penetrating Oil

The lock screw is made of metal, and it is not impossible that it would corrode in a moist area such as the kitchen sink.
If you find it difficult to remove a rusted lock nut, then you can loosen the lock by splashing the correct amount of penetrating oil.
Let the penetrating oil to soak into the nut’s grooves before turning it with a wrench.
The night before you do this task, spray the penetrating oil onto the lock nut.
It will save time and effort.

Step 5: Take out the Basket Strainer

You may disconnect the basket strainer after you have loosened the lock nut and removed the tension protector and the rubber washer that seals the base of the sink’s drain hole.
You may need to provide it a press from beneath the sink to break it away from the thick plumber’s putty.
Give just as much power as is necessary to prevent moving the entire sink basin off the surface.

Step 6: Rinse the hole

Consider the hole created by the drain strainer to be nasty with fragments of dried putty and muck.
Scratch the putty away using a putty knife, then rinse and dry the area to prepare it for the fresh basket strainer.

Step 7: Setup the New Sink Drain Strainer

Rotate the new sink drain strainer above and coat it with plumber’s putty.
Insert the drain strainer into the sink’s drain hole and push it down to create an equal seal with the sealant in between sink and the strainer.
Need not press down on the basket strainer so strongly that all of the putty is ejected off.
Remove any leftover putty that was squished out when you placed the drain strainer into the hole.

Step 8: Make sure the drain hole under the sink is sealed

Go further into sink cabinet and place a rubber-seal washer well above the drain strainer’s base.
Furthermore, when tightening the drainer strainer with a lock nut, place a tension protector layer above the rubber washer.
As you fasten the lock nut, you should grasp the drain strainer with needle-nose pliers so that it does not spin round along the wrench.

Step 9: Join the tailpiece

Join the tailpiece to the bottom of the drain strainer after connecting the basket strainer snugly to the sink’s drain hole.
Regarding concerns of longevity, we recommend using a brass tailpiece more than a plastic one.
Use a ring connector to connect the drainpipes to the tailpiece base.
To avoid breaking this connection or the drainpipes, gently tighten it with a wrench tool.

Step 10: Test for leaks

Switch on the closed valves and open the faucets.
Let the water to flow for a reasonable amount of time while you check the connections for leaks.
Every part with leaks should be tightened.

Video Guide: How to Remove the Sink Drain Assembly

How to Remove Sink Strainer Lock nut

Sink drain locknuts are often composed of soft metal, generally a zinc-based composite that does not rust quickly, although some of them are formed of PVC.

They are small and basically serve to form a strong seal between the drain basket and the bottom of the sink, irrespective of the substance from which they are manufactured.

After installation, the locknuts would only need to be removed if the basket needed to be replaced or if it overflowed.

Connect huge slip-joint pliers to the locknut’s sides.
Rotate the screw anticlockwise.
During rotating, keep a strong grip on the knobs and keep the connection as strong as necessary.
Sprinkle lubricant well above locknut so that it seeps down into the threads.
Start breaking it loose by first rotating the locknut in one direction, and then in another.
When using slip-jointed pliers, heat them up.
Give heat to the locknut using a hair dryer tuned to the highest setting.

Tip: One may use a heat gun as a substitute for a hair dryer, but one should also be cautious.

Anything combustible, such as toilet paper or tissue, will be burned by a heat gun.
Wait for a few minutes so that hot air will be forced into the locknut.
Reconnect the slip-joint pliers and try turning it again.
If the locknut didn’t move with the slip-joint pliers, then hit it with a hammer for a few turns while heating up.
Using the slip-joint pliers, try turning it once more.
Then, use a pair of pliers to grasp the locknut ends and screw them away.
Every time you take off an end, the nut can tend to loosen.
Try to loosen the nut till you can either actually remove it or it starts to detach.
Put the chisel’s pointy end against any of the locknut studs and tap the opposing end slowly using a hammer.
If the substance is made of lightweight metal or polymer, the chisel may start to cut through it.
Chisel back somewhere at the sides, and after that, slash up and down on the nuts using the chisel.
Pry the locknut from the drain basket using pliers after the material has released.
Using a hacksaw, remove the nut.
Slice crosswise through the locknut’s fragile metal or plastic.
Again, when the tip has been crossed, take it off.
When you’re not planning to use the drain basket anymore, position the hacksaw blade in between the sink and the locknut itself and finally cut through the drain basket.

Conclusion

A leaky kitchen sink drain isn’t something that you can come up with for ever.

Anyone may attempt, however pulling out bowls of water underneath your sink can quickly wear your out.

This instruction will assist you in removing your clogged sink drain and replacing it with a more effective one.

Best Guide: How to Clean Sink Drain (8 Steps)

how to

Robert Brown

-

December 24, 2021

0

Hello my dear friends! I think you are in a trouble in cleaning the sink drain. So, only you have came to read this post on how to clean sink drain.

Cleaning shower drain or bathroom sink drain may be tough for you! Some times you don’t know how to start it ?

Do you have a backed up sink in your bathroom that leaves an unpleasant odor?

A clogged sink or clogged drains is always a nasty problem. The good news is that you can fix it using several methods.

There is a solution to most plumbing issues out there, whether it’s by using liquid cleaners or snaking tools. Learn how to clean sink drain with our guide.

Must Read