Home Blog Page 2

Quick Guide: How to Replace a Roman Tub Faucet With No Access Panel (5 Steps)

0

Due to the versatile design of Roman tub faucets, they require a delicate skill to repair.

But how to replace a Roman tub faucet with no access panel ?

For replacing a Roman tub faucet, cut off the water supply and unscrew the set screw to remove the existing spout. You can also carry out the same procedure to remove the handles. Next, enclose the cartridges and spout with o-rings. Don’t forget to add plumber’s putty before installing a replacement handle and spout.

Replacing a Roman tub faucet without access panel is not really as difficult as it sounds. The procedure is straightforward and just involves turning off the faucet and removing any existing nuts.

Everyone can do it, so join us as we explain how to change the faucet on a Roman tub without accessing the panel.

Also read: How to change a bathtub faucet

What is a Roman Tub Faucet?

What is a Roman Tub Faucet ?

A Roman tub faucet is a type of bath and shower faucet which is connected to the tub’s deck rather than the wall. Roman tub faucets can provide an attractive arching appeal and a smooth, classy appearance, which explains their popularity.

Roman tub faucets are a common choice among homeowners since they function very well with solitary tubs. They are available in a wide range of configurations, comprising single, double, and triple handle styles.

Three or more faucet holes are required for the fitting of these faucets, particularly when combined with a hand shower connection.

While Roman faucets are characterised by an arched spout, they are available with a variety of handle designs and attractive finishes.

Whenever it comes to plumbing fittings, the choices might be overwhelming.

You must analyze the several kinds of faucets, their various finishes, and how they will be mounted. However, for a bathtub, a Roman tub faucet is a master piece.

Also read: How to fix a leaky shower faucet

Also read: How to fix a leaky bathtub faucet

How to Replace a Roman Tub Faucet With No Access Panel ?

Replacing a roman tub faucet might be challenging due to the lack of a standard access panel seen on other types of faucets. However, here is an in-depth step-by-step instruction for replacing a Roman tub faucet.

The following is a brief list of the materials you will require for the job:

Materials Required

  • Plumber’s putty (optional)
  • Flathead screwdriver
  • A new faucet trim kit
  • Allen wrench or hex key
  • Putty knife

Step 1: Shut Off the Water Supply

  • Incase an access panel is visible near the tub, then you have to shut off the water at that moment.
  • Perhaps there is an access panel and you are unaware of it.
  • Oftentimes, these access panels are placed in a nearby room’s closet.
  • If you are not able to find any access panels, then switch off the water supply to the home through the main water line.
  • The shut-off valve is most likely located close to your water heater.
  • Switch on all faucets completely and allow them to flow till all the water has been emptied.
  • This procedure protects you from being injured by hot water or flooded by any debris that may have accumulated in the pipelines.

Step 2: Remove the Old Spout

  • With a hex key or Allen wrench, unscrew the set screw.
  • The set screw is a tiny, headless screw located at the bottom of the faucet.
  • If you can’t find it in the first place, then look at the back side. Sometimes, they are supposed to be hidden.
  • Now, you have to remove the old spout.
  • You would do that by pulling it up. If you still find any remaining parts at the bottom of the faucet, you should remove them with the help of a screwdriver.
  • If your faucet base has been caulked or bonded, you might have to insert a putty knife between the base and the tub deck. This will help to remove that.
  • You must repeat the same procedure when dealing with the handles.

Step 3: Unscrew the Set Screw

  • The set screw could be located towards the rear of the handle, similar to the faucet, or at the head of the handle.
  • Incase the screw is hidden below a decorative cover, then pull it out with your flathead screwdriver.
  • When you’re having problems locating a set screw, try rotating the base in the other direction.
  • Wipe away any excess putty or caulk from the tub deck, leaving a clean surface for installing your new tub faucet.

Step 4: Place the Rubber o-rings

  • A rubber o-ring is used at the base of plumbing fittings to guarantee a hermetic seal.
  • Utilize the rings included in your trim-out kit to secure the cartridges and spout pipe.
  • Take your rubber o-rings and put them around your faucet cartridges and spout pipe.
  • Assemble the rings completely, to the bottom, to ensure a snug fit with the tub deck.
  • Plumber’s putty provides an additional layer of protection against spills.
  • To begin with, determine if your type of Roman tub faucet supports the use of putty.

Step 5: Install the New Handles

  • Cover the current cartridges with the new handles.
  • Now, you have to rotate the faucet base clockwise or use your hex key to fasten the set screw.
  • Every model’s installation criteria will be somewhat unique.  
  • Now, you have to insert the spout above your faucet pipe and gently push down to snug it properly.
  • This spout design is unlikely to turn. So, fasten the set screw once the base is flat with the tub deck.

Step 6: Check for Leaks

  • Open up your water supply, switch on your new faucet, and check for leaks.
  • If you find any water dripping, then treat it immediately.
  • Small leaks may increase in size and create big trouble over time.
  • As soon as  your faucet and handles are drip free, you’re fully prepared to use your new tub faucet!

When Should I Change My Faucet Cartridges?

When to replace my faucet cartridges?

Whenever you rotate the handle , the cartridge present in the faucet is meant to regulate the flow of water. Cartridges degrade with time and should be changed.

A leaking faucet or trouble switching on the faucet may indicate that your cartridge requires replacement.

Since faucet cartridges are often built for certain faucets, be sure to get a replacement from the correct brand.

Also read: Install outside faucet with PEX

How to tighten Moen kitchen faucet

Whether I Want to Replace the Faucet Cartridge ?

If only the trim is being replaced, as described above, there is no need to change the cartridges unless they are torn.

But, if you’re having problems controlling the temperature or stream flow, it’s necessary to replace your cartridge.

Once you open up your faucet and notice a murky white substance, then mineral deposits may be the cause of this problem. Putting the cartridge in white vinegar can assist in restoring it to its new condition.

Furthermore, if the cartridge has breaks or has other obvious defects, it is necessary to replace it.

Since cartridges are manufacturer-specific for every plumbing fitting, you’ll have to place a special request with the manufacturer or a specialist seller.

Please remember that cartridges are not always the reason for leakage. Leaks are often indicative of a defective o-ring or washer.

Video Guide: Delta Roman Tub Faucet Repair

Conclusion

Since Roman tub faucets are both efficient and aesthetic, they are a popular option. Therefore, ensure that you know how to change a Roman tub faucet in the event that something awful happens.

Every homeowner’s desire is to have a functional and aesthetically pleasing bathroom. Furthermore, no one loves a dripping roman tub faucet.

Anything would be achievable with some knowledge and an aptitude for design. Simple modifications, such as replacing fixtures, may have a significant impact.

After you’ve completed your job, all you must do is take a short break and relax in your newly refurbished bathroom while resting in your Roman tub.

Related Questions

1. How do you remove an old Roman tub faucet?

Release the screw positioned on the rear of the spout’s base with the help of a hex key. Next, remove the spout by pulling it upwards and/or unscrewing any leftover base parts. You must use a putty knife to scrape the putty below the spout.

2. Are Roman tub faucets interchangeable?

You can change a roman tub faucet if the components are interchangeable. It’s a straightforward do-it-yourself project that anybody can do in a couple of minutes. It’s quicker to replace a roman tub faucet compared to replace a wall-mounted faucet, since they install identically to sink faucets.

3. What is the difference between a garden tub and Roman tub?

In recent times, there seems to be no distinction between such a Garden tub and a Roman tub.

4. What is an access panel for a tub?

An access panel is a door, board, or portion of plywood that could be removed to obtain access to a control valve , drain, or some other plumbing component.

 

Step by Step: How to Tighten Moen Kitchen Faucet ( 5 Quick Steps)

0

Moen kitchen faucets are simple to use and typically durable, and while they may get loose at times.

Fortunately, if your Moen faucet gets loose, all you have to do is adjust the nut. Let’s take a look at how to tighten Moen kitchen faucet.

If you have a loose Moen faucet, the repair is rather straightforward. Additionally, it is very typical for the handle to loosen with time, so you may just do a short repair to restore normalcy. After shutting off the water, you have to tighten the loose nut present at the bottom of the faucet, ensuring that it is securely fastened. This task should take no more than 20 minutes on average.

Moen manufactures a diverse range of kitchen faucets, the majority of which have received praise from critics.

And besides, Moen is a faucet manufacturer, so it’s natural to expect them to provide durable kitchen faucets.

Why Does Your Moen Faucet Become Loose ?

However, what actually occurs when the base becomes loose? And how does this occur?

Base is a little sloppy

With repeated use, both the faucet base and handle would become weak and loose. That is completely normal and causes no concern. Moen faucets, in fact, are designed to endure a long time, so a loose handle is really nothing to worry about.

What Will Happen When Your Moen Faucet is Loose?

Leaking

One of the frequent signs of a loose base or handle is a small amount of water dripping from the faucet. It clearly shows that the joints are no longer secure, permitting small amounts of water to drip out.

If somehow the issue worsens, the leakage will worsen as well. So, it is recommended to tighten the faucet base or handle as soon as possible. While the leakage may not be dangerous, it is an irritation that should be addressed immediately.

Also read: How to change a bathtub faucet

Step by Step Guide: How to Tighten Moen Kitchen Faucet

How to tighten moen kitchen faucet

The great news is that strengthening the base of your Moen faucet is a fairly easy procedure.

Additionally, it does not require any advanced tools. I believe that you will have a majority of these tools in your tool kit. If you don’t have one, then you can buy one from any home improvement store.

Materials Required

  • Hand gloves
  • Mini knife
  • 3/32” Allen wrench
  • Flashlight
  • Adjustable wrench
  • Basin wrench

Step 1: Cover the Basin Drain

  • Begin by sealing the basin drain. This guarantees that neither of the parts, particularly the nuts, will go into the drain.
  • This is a terrible scenario that has occurred frequently for many people.
  • Additionally, it is crucial to avoid these concerns since losing key nuts necessitates their replacement.
  • Actually, taking one of the spare nuts to the hardware shop to get a match is an unnecessary burden.
  • So, it is best to cover the basin drain as a first step.

Step 2: Shut off the Water Supply

  • After properly plugging the basin drain, it’s important to locate and cut off your water supply.
  • Whenever it relates to a Moen kitchen faucet, you’re mostly dealing with two kinds of water delivery valves: the hot water valve and the cold water valve.
  • Those valves are located at the rear of the majority of Moen kitchen faucets.
  • Provide enough light; else, you may have some trouble in identifying the valves.
  • Once you locate the water system valves, turn them both counterclockwise to cut them off.
  • Restart the faucet and check to see that the water is no longer flowing.
  • Assure that the valves are securely sealed in place; otherwise, you may encounter some leakage while working.

Step 3: Release Leftover Pressure

  • Once you switch off the supply valves, the following section is critical.
  • Now you have to open  the handle from your faucet.
  • After that, you’ll want to relieve any built-up pressure in the water pipes.
  • Don’t forget this step, as it will be necessary in subsequent phases.

Step 4: Remove the Water Lines

  • Once the water flow has been restricted, it’s time to concentrate on the faucet’s base region.
  • This is when the adjustable wrench comes in handy, since you’ll need to pull the water pipes apart.
  •  Now you want to connect your adjustable wrench to the supply and intake pipes of the water system.
  • To dislodge them, rotate the wrench counterclockwise.

Tip: Gloves are required here. You could probably get away without them, however there are two advantages. For starters, your hands are more covered. Two, you improve your grip on the wrench, which makes it simpler to loosen the necessary parts.

Step 5: Tighten the Nuts

  • You are now on the verge of completing the job.
  • Thus, the basin wrench is required to tighten the nuts present at the faucet’s base.
  • Later, the nuts may get dislodged, enabling water to seep in slowly.
  • Likewise, if you lack a basin wrench, anyone can purchase it from a home improvement store.
  • With the help of a basin wrench, grasp the nuts and gently apply pressure to adjust them.
  • You don’t  have to overtighten them, however you do want to ensure they are secure.
  • The very last point you need to do is strengthen them just to have the leaks return due to insufficient tightness.

Step 6: Check for Leaks

  • After fastening any loose nuts, it’s essential to reassemble everything.
  • Rejoin your water system valves, ensuring they are securely fastened once again.
  • Next, open the faucet and check for any leakage from the base.
  • If you are not able to see any water leaks, your task is complete.

Also read: How to fix a leaky shower faucet

Also read: How to fix a leaky bathtub faucet

Video Guide: How to Tighten Moen Kitchen Faucet Base

How to tighten a Moen Kitchen Faucet Handle

How to tighten moen kitchen faucet handle

Whenever water begins to spill from your Moen faucet and the base is not the issue, the handle will be the next thing to examine.

Sometimes, a loose handle may be the source of the problem. The best part is that repairing it is exactly as simple as repairing the base.

Step 1: Cut off the water supply

  • Make a clean sweep of the area around the sink and shut off the water supply.
  • It is identical to the procedure outlined before and will prevent water from messing with your job.

Step 2: Remove the hex nut

  • Examine the faucet to see which part is malfunctioning.
  • This is when the faucet’s style becomes important.
  • The hex nut or screw should be removed.
  • If you check within the handle of your faucet, you may discover a screw or hex nut.
  • You should carefully pry it out with a mini-knife or screwdriver.
  • Due to the fact that these screws are often composed of plastic, you must be careful.
  • This will take no more than 2 minutes.

Step 3:Tighten the Screw

  • Incase you do not see the setscrew in that location, look under the cap.
  • To remove the screw from this location, you will need the help of an Allen wrench.
  • The most commonly required size is a 3/32″ Allen wrench. The most difficult aspect is probably finding the main screw.
  • Adjust the screw. As soon as you locate the screw, tighten it by twisting your wrench clockwise.
  • Ensure that it is tight. You should also avoid overtightening.
  • Rejoin the supply of water. Rejoin and check your water supply valves.

How do you remove a moen faucet handle?

How to remove moen kitchen faucet handle

If you suspect a more serious problem, you may need to completely remove the faucet before attempting to repair it.

However, disconnecting the faucet is fairly straightforward process and requires even less materials.

Everything you want is a screwdriver, a wrench, and a pair of needle-nose pliers to unscrew your Moen faucet.

Incase you do not already own these equipment, it is a wise idea to get it for a variety of ordinary tasks around your home.

Step 1: Cut off the water supply

  • Just like with strengthening the base or handle. Ensure that both lines are turned off.

Step 2: Empty the Pipe

  • Open your faucet to see whether there is any water within. Allow it to drain completely before dismantling.

Step 3: Take out the handle

  • Take off the handle.
  • Release the handle with the help of your screwdriver and afterwards remove the setscrew that secures it to the faucet.
  • Once you have properly loosened it, the handle might come free.

Step 4: Remove the Cartridge

  • Once the handle is removed, a dome will appear.
  • You can simply glide it out, next rotate the black jacket till it releases.
  • From this point on, all that’s left are screws and loose pieces.
  • Disconnect the spout by unscrewing the handle, detaching the ring and the washer, and then pulling it out.
  • Next, using your pliers, take out the cartridge to ensure that the faucet has been entirely removed.

Also read: Install outside faucet with PEX

Conclusion

Whenever you understand how to tighten a loose moen single handle kitchen faucet, you won’t have to worry about anything coming loose in your faucet.

You may not be feeling confident right now, but I want to tell you that it is really simple to do this task.

As well as the experience itself, will be enjoyable in its own right.

I hope you liked this post.

Related Questions

1. Why does my kitchen faucet keep coming loose?

One of the most frequent causes of a loose kitchen faucets is improper tightening of nuts. The faucet head and base are secured together by a nut. It is generally situated at the bottom of the mount. Its thread will wear down over the course of time.

2. How do I find the Moen faucet model number?

Your box or instruction sheet will contain the precise model number. If somehow, the family series number is unknown, it can be found on the backside of the spout.

3. Where do the O rings go on a Moen kitchen faucet?

Underneath the faucet assembly, you will find O-rings. Detach the screw that secures the handle cover on your Moen faucet using a screwdriver. Otherwise, remove the handle cap away from the faucet using a flat head screwdriver.

Step by Step Guide: How to Install an Outside Faucet With Pex ( 5 Quick Steps)

0

I Know why you are came to read this post ?

It’s nothing, but you don’t know how to install an outside faucet with PEX piping.

How to install an outside faucet with PEX piping

If I am right, then you don’t have to feel about it! I will help you to install that outside faucet along with PEX through my step by step process.

Many people will feel difficult it they don’t have an outdoor faucet in their home. Because it will help them a lot for example, if you have a garden in your backyard, you need water for your plants.

In that time your outside faucet will help you to finish this job.

So this simple DIY Project will help you to install an outdoor faucet with PEX piping. You won’t have to spend lots of money in this project.

You can finish it yourself with some tools and a little bit knowledge.

So, without wasting your precious time, let us see how to start it.

Things to do before installing an outdoor faucet

Things to do before installing outside faucet with PEX

There are certain things you want to do before placing an outdoor faucet in your home. this is also known as Pre-planning.

  • First of all, you should confirm the location where you want to install the outdoor faucet.
  • If you asked me, I will suggest you to choose a place, that is near to your plumbing area within your home.
  • Why I told that means, It will help to make an easy connection once you have installed your outdoor faucet.
  • Try to check the basement area to locate the water pipe running closer to your outdoor faucet.
  • As soon as you choose the correct location for installing your outdoor faucet and the nearby pipes to make the connection, you are ready to start the main job.

Materials Required

These are the list of tools and materials you will need to finish this job.

  • Threaded tee
  • Soldering iron and solder wire
  • Cleaning brush
  • Rag
  • PEX fittings
  • Nailing plates
  • Frost-free Sillcock faucet
  • Drill
  • PEX cutting tool
  • Silicone sealant
  • PEX piping
  • PEX clamp
  • Galvanized screws
  • Copper cutter

Also read: Fix leaking Outside Faucet

Step by Step: How to Install an Outside Faucet With PEX Piping

How to install an outside faucet with PEX piping

Here are the steps that you should follow to install an outside faucet with PEX piping.

Step 1: Shut off the Water Supply

  • First and foremost step, you should do is to shut off the water supply.
  • You may either switch off the water supply to the specific pipe where you will be working or turn off the main water valve to your residence.
  • Remember that it will block the water supply to your whole house, until it is turned on.
  • Let’s go to the next step.

Step 2: Drill to Mount the Faucet

  • To install the outside faucet, start by drilling a hole in the basement wall at the spot where you want it to be.
  • The hole has to be 1 inch in diameter in order for the sillcock faucet to fit through it properly.
  • Insert the sillcock faucet into the opening on the outer wall.
  • After inserting, take some galvanized screws to secure it to the wall on both sides.
  • Inspect the faucet to ensure that it is oriented downward toward the interior of the home.
  • This added approach will help to protect the water from freezing in the wintertime.
  • Tip: A silicone sealant should be used to secure the connection.

Step 3:Connect PEX Adapter

  • Make your way to the interior of the home to locate the other end of the sillcock faucet that you just completed installation of.
  • Then, using a copper cutter, trim the water pipe from where you’d like to make the connection.
  • Ensure a bucket is positioned beneath the sink since any water that accumulates in the pipelines may drain into it without causing a mess on the floor.
  • Now, you have to mount the threaded tee at the place, where you have created the cut and connect the pex adapter to the free end of the threaded tee.
  • Weld all of the new joints to the water pipe together using a soldering iron to keep them in place.
  • Remove any remaining remnants with a cloth.

Step 4: Connect the PEX Adapter

  • Retrace your steps back towards the end of the sillcock faucet that is located inside the home.
  • Wash the end from the inside to ensure that nothing is obstructing the water’s flow route to the outside.
  • This would be completed with the help of a cleaning brush.
  • The PEX adapter should be oiled. once you have oiled the adapter, mount it to one end of a new water cutoff valve.
  • After that, you must connect the cutoff valve to the tip of the faucet, with a copper fitting somewhere between, to complete the installation.
  • Before connecting the pieces, lubricate all of the ends.
  • All of the new connections should be secured in place with the help of a soldering iron as well as some soldering wire.
  • Remove any solder dust from the connections by wiping them with a cloth.
  • Now, leave the connection to rest before fitting the PEX pipe.
  • This is due to the fact that it is made of plastic and may melt.

Step 5: Install the PEX Pipe

  • Attach your PEX pipe into the free end of the connection you created between the water pipe within the home .
  • Now, you have to position it in a PEX clamp and twist it to ensure that the connection is secure.
  • Extend the PEX pipe above the ceiling of your basement.
  • You should also fasten it with 1-inch PEX clips at appropriate intervals throughout the length of the PEX pipe.
  • Take the PEX pipe all the way around to the inside of the faucet, attaching it at the top all the way down the length.
  • Trim the PEX pipe using a PEX cutter at the place where you want to establish a connection to the faucet.
  • With the help of an expansion tool, attach it to a PEX adapter at the other extremity of the faucet.
  • Make use of a PEX clamp to secure the connection in the same manner as you performed at the other side.

Step 6: Turn on the Water

  • Now you have to check that your outdoor faucet is working or not.
  • For that, you have to turn on the water supply line to your home.
  • Open the Main water valve that supplies water to your whole home or just the water pipe you were working with.
  • Turn on the cutoff valve that you put on the inner end of the faucet as well.
  • Step outside and turn on the outside faucet.

That’s all, you have successfully completed this job.

Video Guide: How to install Frost-Proof Faucet with PEX Tubing

Video Guide: How to Connect Outside Water Faucet to PVC Pipe

 

Also read: Outdoor Faucet Won’t Turn Off

Best Outdoor faucet to buy

Conclusion

Look how easy it was. You’ll also have pleasure installing your own DIY outdoor faucet if you have your mind set on it!

Furthermore, you’ll be going to save a big money in installing the faucet. The actual process isn’t that difficult after you’ve learnt how to install an outdoor faucet using pex.

This will only take you about an hour to finish the whole thing, and the end product will be well worth your time!

You’ll have water right where you really need it, whether it’s for feeding your garden, cleaning your vehicle, or any other outdoor activity you have planned.

 

Related Questions

1. Why is PEX plumbing bad?

Compared to copper pipe and galvanized steel pipes, PEX pipes are more susceptible to damage as a result of their high permeability and flow rate.

For example, a rat may readily eat through them . Chemical Issues — Some varieties of PEX have been shown to leak hazardous chemicals and impurities into the environment, altering the taste and odor of drinking water.

2. Is PEX safe for drinking water ?

Due to worries about harmful compounds escaping through the pipe and into the water supply, PEX was prohibited in California. A variety of national laboratory examinations have shown that PEX is entirely safe and long-term in nature. It is currently permitted in California, and it is even listed in the state’s primary plumbing rules.

3. How long will PEX last?

PEX has also been subjected to extensive long-term testing, which has shown that it has a possible lifetime of more than one hundred years.

4. Where is PEX not allowed?

PEX cannot be put in high-temperature environments. It is not possible to install PEX in high-heat places, such as near recessed lights. This also implies that you can’t connect PEX straight to a hot water heater, but you may do it with the use of a connecting element instead.

5. Should I use PEX or copper?

In our opinion, PEX Tubing is superior to copper tubing in the vast majority, but not all, of plumbing transition fitting. It also cost less than 100 dollars to finish the job.

6. Do PEX pipes burst when frozen?

Even though PEX freezes, it pops, very much like copper and CPVC, and this is a known fact. There is no material that can withstand the amazing power and pressure that is associated in freezing. The only trusted method of preventing a frozen tubing from exploding is to protect the pipe or cold water line from freezing in the first spot, as previously stated.

Step by Step Guide: How to Change a Bathtub Faucet ( 11 Quick Steps)

0

Whenever your bathtub faucet is old or damaged, you may simply replace it with a new one by doing the installation yourself.

It makes no difference whether you have a single-handle faucet or a tub faucet with many controls; the procedure is still the same.

Then, how to change a bathtub faucet?

If you wish to change your bathtub faucet handles, you must first remove them from the faucets, as well as the stems that link them to the pipelines. Replace your spout by simply unscrewing the old one and screwing in the new one; it couldn’t be much easier! Upon completion, you will have brand new faucets that will make your bathtub sparkle!

Also read: How to fix a leaky bathtub faucet

Step by Step : How to Change a Bathtub Faucet

How to change a  bathtub faucet

Step 1: Shut off the Water Supply

  • The fact that most bathtubs do not have a distinct shut-off valve means that you must switch off the water supply to your whole house.
  • The main line in your house should be located, and it should be turned perpendicular to the pipelines.
  • Even when you’re operating on your tub, this will prevent any water from entering in from the outside.
  • It is possible that your water supply pipe is located in your basement or even outside your house.
  • If you’re not sure how to cut off the water supply to your house, you should call a plumber for assistance.
  • This shutoff valve will prevent any other fittings in your house from using water while the water is turned off.

Step 2: Remove the Index

  • Empty the bathtub water by turning one of the knobs so the water drains out of the tub spout.
  • There will be an amount of water remaining inside your pipes, which will be flushed away.
  • As soon as you see that water is no longer pouring out of the spout, switch the tub faucet off once more.
  • The index is normally a coin-sized plastic cap in the center of the handle.
  • Insert the tip of a flathead screwdriver beneath the index’s tip and pull it out.
  • The length of your index will be determined by the number of handles you have.

Step 3: Remove the Bathtub Handle

  • After removing the index cover, there should be a screw within the hole.
  • To remove the lever from the faucet stem, use a screwdriver to rotate the screw counterclockwise.
  • It is recommended to keep the drain closed to stop the screws from falling in.
  • Keep your screws in a safe place where you can easily locate them later.

Step 4: Pry off the Stem

  • The stem is the thin pipe-like structure that protrudes from the wall and regulates the faucet.
  • Insert a hollow socket wrench key above the stem and press it against the hex nut.
  • Hold the wrench with the help of a pair of pliers and rotate it counterclockwise.
  • Pry the stem away from the wall after it has become free.
  • A socket wrench designed for pipelines could be purchased at your local hardware shop.
  • If somehow the nut protrudes beyond the wall, simply release it using a pair of pliers.
  • If your bathtub has more than one handle, go through the procedure again for each one.

Step 5: Remove the Screw

  • Your nozzle may be held in place with a mounting screw.
  • So, you have to find the screw below your spout and twist it counterclockwise with the help of an Allen wrench.
  • When the screw is removed, the faucet will easily pull away from the pipe.
  • Incase your bathtub spout lacks a screw, leave this step.
  • Ensure that you have blocked your drain so you don’t lose the screw by mistake.

Step 6: Remove the Tub Spout

  • Using pliers, grasp the spout and turn it counterclockwise.
  • As soon as the spout is free, detach it from the wall with one hand.
  • Remove the spout from the tube.
  • Calculate the length of the piping that was present within your faucet.
  • You can finish this process using a tape measure.
  • Make a note of the measurement so you can recall it later.
  • When purchasing a new bathtub spout, make sure it is longer than the piping protruding out of your wall.

Step 7: Choose the Correct Handle and Stem

  • When searching for a new faucet, take your existing stems and handles along with you.
  • Ensure that you get stems that are identical to your previous ones ( old faucet) such that they will simply slide onto your pipelines.
  • Then choose a handle that complements the other fittings in your bathroom.
  • Stems and handles are available in the plumbing area of your home improvement shop.
  • Make sure to pick handles that are compatible with your system.
  • For example, if your previous faucet had many handles, you can’t load a single handle.
  • Certain retailers provide kits that include stems and handles for simple setup.

Step 8: Install the New Stem

  • When you get the new stem, insert the slotted end into the position where your previous faucet used to be.
  • Next, you should stiffen the stem with your hand and fasten it to the pipes by turning it clockwise.
  • Once the stem is hand-tight, take the pliers and your socket wrench to secure the joint.
  • Whenever your tub has many handles, be sure you install a new stem for each one.

Step 9: Replace the Index Cap

  • After you’ve fastened the stem, slide your new handle above it and press it back until it meets the wall.
  • As soon as the handle is present on the stem, fasten the screw with your screwdriver to attach it to the stem.
  • To complete the handle, place the index cap above the screw.
  • Continue with the other handles you currently have in your bathtub.
  • When your handles aren’t waterproof, you’ll have to caulk around them to keep water out of your sidewalls.

Step 10: Purchase a New Spout

  • Now you have to buy a new spout from your local home improvement shop.
  • Search for something that complements the handle on your bathtub.
  • Ensure that the replacement spout is lengthier than the pipe size you measured.
  • If you don’t attach the spout that’s fastened in the same manner as your previous one, it could not stay intact.
  • Carry your existing spout so that you can get something close in length.
  • Incase you want all of your fittings to coincide, check for sets that include handles and spouts.
  • Plumber’s tape keeps the tub spout from spilling back toward the wall.
  • So you have to apply 1-2 thicknesses of plumber’s tape around the pipe threads emerging out of your wall.
  • Secure the threading by cutting the tape and pushing it firmly with your fingertips. 
  • You can buy the plumber’s tape from any home improvement shop.

Step 11: Install the New Spout

  • Start rotating your replacement spout clockwise after sliding it above the pipe.
  • To avoid damaging your pipelines, always adjust the spout by hand.
  • Continue tightening the faucet until it becomes hard to turn.
  • If the spout is not facing down, spin it counterclockwise until it does.
  • Incase your pipe is too small and the spout does not clamp on, you might have to purchase a spout adapter.
  • This part serves as an extension for your pipeline, allowing you to plug in the faucet.
  • Fasten the adapter onto the pipe. After that, twist the spout onto the adapter’s tip.
  • Finally, fasten the screw on the base of your spout using an Allen wrench to hold it in position.
  • Restore the water flow to your home after all of the new fixtures are in set.

Video Guide: How to Replace a Bathtub Faucet

How to fix a Broken Bathtub Faucet Handle

Fix a broken bathtub faucet

  1. Ensure that the water supply to the bathtub that you will be repairing on is turned off. Shutoff valves are frequently found in supply enclosures or closets.
  1. Disconnect any plastic caps that may have been attached to the faucet handle, and then unscrew the handle screw.
  1. Now, you have to start pulling the handle away from the stem in a straight line.
  1. Disconnect the valve stem from the faucet by unscrewing the hexagonal packing nuts that are located at the head and base of the stem.
  1. Remove the washer from the stem by loosening the locking nut at the base of the stem using a flathead screwdriver.
  1. Remove any calcium or grit layers with a blade, install a new washer, and tighten the locking screw to ensure it is safe.
  1. Cover the threads of the valve stem with plumber’s tape, completing at least 2 rounds and stripping off every extra tape. Replace the valve stem in its socket and adjust it with a wrench to ensure that it is secure.
  1. Fasten the packing nut by sliding it into the stem.
  1. Now, you have to reinstall the faucet handle well above the stem and fasten it with the handle screw.
  1. You may also want to check whether you have placed the protective cap or not.
  1. Finally, open water supply to the area. You have now learnt how to repair a faulty bathtub faucet handle. Congratulations!

These procedures should assist you in identifying the cause of the majority of minor leaks.

After you’ve mastered the art of repairing a broken bathtub faucet handle, you could use most of the same techniques on your sink faucet and kitchen faucet as well.

If the handle on your shower faucet has come loose, you may replace it by using the same procedure.

How to Change a Bathtub Faucet Washer

How to change a bathtub washer

  1. Restrict the water flow to the bathtub faucet and turn off the water valve. If you are unable to reach your bathtub shutdown valve, you may turn off the water supply to the whole home.
  1. Shut or seal the bathtub drain and wrap it with a cloth to collect any pieces or screws that may fall into the drain mistakenly.
  1. Using a flat-head screwdriver, pull the decorative cover away from the faucet handle and discard it.
  1. Loosen the screw from the interior of the handle and take the handle away from the valve assembly to complete the removal.
  1. To release the locking nut from the valve assembly, use a pipe wrench to twist the nut, which is now visible on the valve assembly.
  1. Remember to turn it counterclockwise. Rotating the valve assembly counterclockwise will allow you to remove the complete unit.
  1. Disassemble the valve assembly and unscrew the screw that keeps the old washer in position.
  1. Remove the existing washer by carefully pulling it off with the help of a flat-head screwdriver. 
  1. The edge of a screwdriver could be used to scrape any remnants of the old washer that may have remained on the valve assembly after it was removed.
  1. Now, you need to mount the replacement washer in the same location as the old one.
  1. Remember to adjust the washer to the valve assembly using a screw. After that, reinstall the valve assembly to the fitting by twisting it clockwise with the help of a pipe wrench.  
  1. Reinstall the decorative cap on the tap handle once it has been screwed down onto the valve assembly.
  1. You can also try out these procedures for the other faucet.

Also read: How to fix a leaky compression faucet

Fix a leaking sink drain pipe

Fix a leaking shut off valve

Wrap Up!

Replacing a bathtub faucet is not a major task, you can do it with the help of few tools and guide. If you still can’t able to change your bathtub faucet then you must call a professional plumber to help you out. If you liked guide, subscribe to our newsletter to get information about sinks and faucets

Quick Guide: How to Fix a Leaky Compression Faucet (5 Steps)

0

We understand that paying a plumber for a repair is frequently an unexpected and unwanted expenditure.

Therefore, you may be looking online attempting to figure out how to fix a leaky compression faucet on your own.

If your compression faucet leaks from the spout, then replacing the washer can fix this problem. Incase your compression faucet drips from the handle, then the first thing you should do is tightening or changing the packing nut.

Even the smallest drips and leaks may add up to a large amount of water loss and bills over time.

It’s important to understand how to fix a leaking compression faucet, which is the most popular kind of kitchen faucet found in houses, in order to prevent wasting time and financial resources.

Let’s see them in our detailed guide.

Also read: How to fix a leaky shower faucet

How to fix a leaky outdoor faucet

How to fix a leaky sink drain pipe

How to fix a leaky compression faucet

What is a compression faucet ?

There are two primary kinds of faucets available: those that have washers and those that do not have washers (washerless faucets).

In the world of faucets, compression faucets are the most simple washer style faucets which has been around since the invention of indoor plumbing.

When it comes to wash basins, compression faucets are often used in laundry rooms, however they may also be seen in kitchens and bathrooms, particularly if the fittings are older ones.

Compression faucets, which feature two distinct knobs for hot and cold water, are the least expensive form of kitchen faucet available on the market.

However, they are also the most prone to leaking and needing maintenance during their lifetime.

When you twist each lever on a compression faucet, a washer or seal expands and shuts against the valve seat at the end of the trunk, allowing or restricting water flow across the faucet body.

This may seem complicated, but it all quickly becomes clear that a worn or broken washer or seal within the handle may allow water to flow when the taps are turned off. This is a common occurrence.

Why is your compression faucet leaking ?

Why your compression faucet is leaking

  • Compression faucets, however, are much more susceptible to leaks than other faucet kinds, and they also need more care.
  • Since leaks are so frequent, it’s crucial to understand the reasons and how to fix a leaking compression faucet.
  • A worn-out washer is the most typical cause of a compression dripping faucet.
  • The washer within the faucet turns off the flow of water whenever the handle is adjusted.
  • It may wear down over time. Whenever the washer stops working, the water flow continues, causing the faucet to overflow.
  • To prevent a leak with this sort of plumbing fixture, it’s usually necessary to replace the washer.
  • Leaks may also be caused by a faulty O-ring.

Step by Step Guide: How to fix a leaky compression faucet

Step 1: Cutoff the Water Supply

  • Search under your kitchen sink for a little cutoff valve that shuts off the water supply.
  • Close the valve by rotating the lever clockwise.
  • The water system for the house should be turned off at the home’s primary cutoff valve or at the water meter if there aren’t any shutoff valves beneath the sink to do so.
  • Once the water has been turned off, completely open the faucet to relieve any pressure or leftover water that may have built up in the line.

Step 2: Take off the faucet handle

  • A screw hidden behind a decorative cover connects the handle portion to the faucet valve stem assembly.
  • With older faucets, the cover is often metallic, and bolts are screwed into the handle.
  • Grasp the cap with pliers and detach it to obtain access to the screw that holds the faucet handle in place.
  • Incase your cap is plastic, pull it off with the help of a little flat-blade screwdriver.
  • Metal caps on certain faucets may be pryed off as well.
  • What’s the greatest approach to figure it out?
  • It’s most likely a screw-off cap if the metal top has grooves around the circumference.
  • The cap will most probably prick off if it is narrow or has a smooth border.
  • With the help of a Phillips screwdriver, you can unscrew the screw that secures the handle to the valve stem.
  • To take off the handle from the valve stem, you should lift it upward.
  • If somehow the handle becomes stuck, you might have to release it using a compression faucet handle puller.

Step 3: Disassemble the Stem Assembly

  • After removing the handle, you will see a cover well above the valve stem assembly.
  • Using pliers, loosen the clamping knob that keeps the stem assembly cover in place.
  • Even when no cover is present, check for a hex-nut piece of the valve stem assembly, which is normally found in the area where the assembly joins the faucet body.
  • To release the valve stem assembly, grab it with pliers or an adjustable wrench and rotate it counterclockwise.
  • Remove the valve stem assembly from the faucet body by unscrewing it completely.

Step 4: Change the Old Washer

  • Find the old washer, which should be resting on a valve seat near the base end of the valve assembly.
  • It would be kept in place by a screw, and it would most certainly be worn out or distorted in some way.
  • Loosen the brass nut that is keeping the washer in place.
  • Remove the rubber washer from the valve seat by inserting a tiny flat-bladed screwdriver into the opening in the washer and prying it out with it.
  • Remove any deposits or leftover rubber from the tip of the washer holder to ensure that the new washer settles smoothly into the valve seat when it is installed.

Step 5: Apply Plumber’s Grease

  • It is possible that you may need to purchase an array of washers, which are generally given together as a faucet repair kit.”
  • Additionally, a replacement for the rubber O-ring that surrounds the valve stem assembly is available upon request.
  • Now, you have to insert the new washer into the valve seat, and tighten the washer with the help of a brass screw to prevent it from moving.
  • If you find a damaged O-ring, then you have to replace it with a new one.
  • Next, you should apply a thin layer of waterproof plumbers grease on the exterior side of the O-ring (whether it is old or new).

Step 6: Examine for Leaks

  • Using pliers, insert the valve stem unit into the faucet body until it is firmly fastened in place.
  • Finally, you have to reattach the handle and cap to their previous positions.
  • Next, switch on the water system and look for leaks in the faucet.
  • If your compression faucet still drips, then contact a professional plumber to fix your problem.

Also read: How to fix a leaky shut off valve

How to Fix a Leaky Bathtub Faucet

Repair Compression Faucet Handle

Repair Compression Faucet Handle

  • If you have a compression faucet leak from the handle, the first thing you should do is tightening or changing the packing nut.
  • Incase this does not work, you would have to change the packing, which would be a seat washer, an O-ring, or in some instances twine, that is looped all across the compression stem to prevent the compression stem from moving.
  • Don’t forget to cut off the supply of water before beginning any changes, and to release both the cold and hot water faucets to enable the water to flow out of the faucet.

Also read: How to fix a leaky delta faucet

Video Guide: How to Repair an Old Compression Faucet

Video Guide: How to fix a leaky kitchen faucet

Conclusion

We hope you enjoyed our post about how to fix a leaky compression faucet! We know that it can be frustrating when the faucet starts to leak and drips constantly, so we wanted to provide some helpful advice on how to fix it yourself.

Related Questions

What is usually the cause of a leak in a compression faucet?

Damaged washers might be the cause.

The washer that lies against the valve seat is another major source of spout leaking. It is also possible for a faucet to drip if the washer is placed wrongly or is the improper size. This is most often seen in compression faucets.

What is a common failure part in a compression faucet that is leaking out of the spout ?

Rusted Valve Seat

As a component of the compression system, valve seats are used to link the faucet and the spout. The buildup of water particles over time causes the valve seat region to erode, which results in a leaking faucet as a result. This rusting causes leaking along the spout’s perimeter.

Why does my faucet drip after I turn it off?

Whenever your faucet continues to leak water after it has been turned off, it may be due to a loose or defective seat washer. Because of prolonged usage, the seat washer screw might become loose, resulting in the faucet dripping water or buzzing. Plastic valve cartridges in modern faucets might have to be changed on an as-needed basis.

What is the most frequent failure part in a typical faucet?

The valve is the component that fails very often. Debris from the water going through the faucet accumulates and worsens the valve, causing leaks to occur as a result.

Step by Step Guide: How to Fix a Leaky Sink Drain Pipe (4 Quick Methods)

0

It’s always such a hassle when you find a damaged or leaking pipe in your sink’s drain.

If you detect a leak, it typically implies that your pipelines are weak, broken, or worn out. You may ask how to fix a leaky sink drain pipe?

Thankfully, fixing your leaking drain and pipes is fairly basic and you can do it at home with a few resources. If the spill flows from the pipes, then it can be from weak joints or breakage. To fix this, apply some epoxy putty to stop the leaks. If the leak emanates from the bottom of your bathroom sink, then replacing the sink strainer can fix the problem. If your pipes are still leaking, then replacing the p-trap can solve this problem.

Let’s begin with some simple and quick repairs to prevent any leaky pipes, and then discuss more substantial options depending on where you detected the problem!

Also read: How to fix a leaky delta faucet

How to fix a leaky shower faucet

How to fix a leaky outdoor faucet

How to Fix a Leaky Sink Drain Pipe

How to fix a leaky sink drain pipe

Repair a Leaky Sink Drain Pipe Using Epoxy Putty

Step 1: Locate the Slip Nut

  • Two part epoxy putty is composed of a base and an adhesive and when combined, they form a seal around the pipe they’re applied to.
  • Simply mix both putties together in your hand until they’ve been completely mingled.
  • Then, using your fingers, push the putty into the part of the pipe that is leaking until it is about half inches thick.
  • Allow the putty to set for the specified period of time given on the container before flushing water down the drain to ensure proper finish.
  • It is possible to get two part epoxy putty from a hardware shop.
  • It is perfect for use with any kind of leaking pipe.
  • Even though the putty is successful in stopping the leak, you should search for a more permanent repair as soon as possible, because this method, only gives a temporary fix.

Step 2: Change the Rubber Gaskets

  • Even though it is designed for low-flow leaks, silicone tape performs better when used across the connections in your drain pipe.
  • Stretch the tape firm and roll it tightly around the pipe, covering 1⁄2 of the piece beneath it with every round of the tape reel.
  • Continue to wrap the tape around the leak beyond the corners of the leak to ensure that it produces a hermetic seal.
  • Silicone tape will not attach immediately to your pipe, but it will adhere to itself, making it simple to remove afterwards if necessary.
  • Furthermore, it fits on any kind of pipe, which makes it quite versatile.

Step 3: Mount the Clamp

  • In order to connect to the pipe, clamps contain a flexible rubber element called a gasket and a metal fastening that goes around it.
  • Just make sure you choose a clamp that has the proper size for your pipe in order to ensure a tight seal.
  • Make sure the gasket is securely compressed against the part of pipe that is dripping.
  • It is recommended to mount the clamp on the head of the gasket and tighten it all around the pipe.
  • Now, using a wrench, screw the clamp all the way down so that no water can leak.
  • Clamps can be used on any sort of pipe that has to be repaired.
  • Clamps should not be used on junctions or corners because they will not fit correctly around your pipe’s circumference.

Also read: How to fix a leaky shut off valve

Repair a Leaky Sink Drain Pipe Using Plumber’s Tape

Step 1: Locate the Slip Nut

  • A lot more these days. All you have is a weak slip nut, which is a circular fastener that connects two pipes together.
  • Locate the first slip nut, which is located in the area below your kitchen sink.
  • Then, you have to rotate the slip nut in the opposite direction of the clock until it becomes hand-tight.
  • Continue working your way down the tube, adjusting each and every nut along the way.
  • You should avoid overtightening the slip nuts, as this might cause damage or stripping of the nut.
  • Pour some water into your drain and see whether there are any leaks left after that.
  • It is possible that there are slip nuts present; if so, tighten them by a quarter-turn using a pair of pliers.

Step 2: Change the Rubber Gaskets

  • Gaskets are the little rubber bits that slip between pipes to create a watertight seal, preventing water from entering.
  • You have to remove the rubber gaskets from the drain pipe by loosening the slip nuts that run along the pipe.
  • After removing the gaskets, inspect them for breaks or damage.
  • Incase you find any breakage, change the old gaskets with new ones that are the same size as the originals.
  • Many gaskets will have a broader end and a smaller end, with the wider end being the more common.
  • Now, you should insert the thin end of the gasket into the pipe using your fingers.
  • It is preferable to put the rubber gasket directly into the tube when changing the gaskets on a slip nut, as shown in the illustration.
  • Ensure the thinner end of the gasket is pointing in the direction of the end of the pipeline where you’ll be connecting the two pieces.
  • The plumbing area of your home improvement store will have new gaskets that you can purchase.

Step 3: Wrap the Plumber’s Tape

  • Plumber’s tape, often known as Teflon tape, is used to form a watertight seal when pipes are connected together.
  • If you still have metallic sink drain pipes, you will need to loosen the slide bolts that hold them in place.
  • Roll the plumber’s tape around the threads in a clockwise direction, covering each turn by 1/2 the breadth of the tape.
  • Before breaking the tape, continue to wrap till you reach the threaded ends and putting your kitchen sink drain back together.
  • Avoid wrapping the tape around the pipe in a counter-clockwise direction because it may stiffen up or tear when you connect the pipeline back into the bathroom sink drain.
  • It is not recommended to use plumber’s tape on PVC pipe or plastic tubes because it may force the pipes to be overtightened or cracked.

Also read: How to fix a leaky bathtub faucet

Fix a Leaky Sink Drain Pipe Using P-trap

Replacing p trap

Step 1: Empty the Remaining Water

  • In spite of the fact that your drain pipe is not dripping with water, leftover water may get trapped in the P-trap.
  • The P-trap is nothing but the J-shaped section of leaky drain pipe which is present below your sink.
  • I recommend that you empty the area under your drain pipes so that you can place a bowl or container right beneath your drain pipes to collect any water.
  • Depending on the model, some P-traps feature a screw-off valve at the bottom that may be used to empty the remaining water.
  • If you have a situation like this, you can simply rotate the P-trap valve counter-clockwise to empty the leftover water.

Step 2: Remove Slip Nuts

  • Slip nuts are the spherical fasteners that link two pipes together.
  • You should begin with the slip nut at the point where your sink drain attaches to the single vertical pipe below your sink.
  • To thoroughly release the nut, twist it clockwise.
  • Keep following the water pipe and unplug any additional slip nuts till you find the horizontal pipe that is emerging out of your wall.
  • As soon as you remove the slip nuts that are connected to each length of pipe, the segment would simply separate.

Step 3: Cut off the Water Supply

  • If just the J-shaped piece of the P-trap is destroyed, you will simply need to unscrew the slip nuts that link that particular piece of water pipe.
  • The other pipelines that are linked to your drain and wall may be left in place.
  • Note: You should ensure that nobody uses the kitchen sink once you have disconnected any drain tubes, or otherwise water will run into the floor from the sink.
  • If possible, you can switch off the water supply immediately at your sink to ensure that nobody ever uses it.
  • Locate the supply valve that is linked to the wall and rotate it clockwise to cut off the water supply.

Step 3: Purchase New P-Trap

  • Take your P-trap, as well as every other drain pipe that you have removed, to the hardware shop near your home.
  • Your modern P-trap package will include all of the pipes, gaskets, and slip nuts that you will need to complete the installation.
  • Please double-check that the replacement kit you purchase has a P-trap and pipes that are precisely the same dimensions as your original ones, or else they will not fit correctly.
  • Most P-trap kits are constructed of PVC, which makes them simple to install and disassemble, but you may also purchase metal drain kits if you like.

Step 4: Attach the Slip Nut

  • Join your drain with the longest portion of pipe.
  • Insert the slip nut into the drain’s threading while holding the head of the piping against the base of your sink’s drain.
  • To fasten the slip nut into your drain, simply rotate it counter-clockwise.
  • A hinged washer, which is a circular rubber component that fits into the pipe’s tip, may be included along with the pipe.
  • Incase your P-trap package includes a washer, then insert the thinner end of the washer into the drain pipe.
  • The trap arm is a small portion of pipe that stretches out through your wall at a sharp angle.
  • You should place the broader end of a flanged washer on the trap arm’s upright edge.
  • The trap arm should then be slipped into the drain pipe protruding from your wall, forming a hermetic seal with the washer.
  • The trap arm may then be secured in position by tightening the slip nut.

Step 5: Mount the New P-Trap

  • Attach the trap arm and the upright drain pipe with the slip nuts and flanged washers.
  • You should also ensure that the washers’ thin ends face toward the tube’s open or free end.
  • Then, you have to mount the P-trap on the endpoints of the pipelines and twist the slip nuts till they are tight and firm.
  • There’s no need to apply any sealer or pipe adhesive, because you’ll want to disassemble the P-trap later.

Step 6: Check For Leaks

  • Switch on the faucet and pour the water down the drain in your sink.
  • Keep an eye on your pipelines and fittings to make sure no water is seeping out.
  • If water drips, then you have to twist your slip nuts a quarter-turn counter-clockwise using a pair of pliers.

Fix a Leaky Drain Pipe Using Sink Stopper or Strainer

How to repair a sink drain pipe

Incase your leak is coming from the point where your drain meets your sink, you might have to change the strainer immediately.

Step 1: Loosen the Slip Nut

  • Food is prevented from going into your pipes by using a sink strainer, and it is also where wastewater flows out of your sink.
  • By crawling below your sink, you can locate the spherical slip nut that is located between the straight drain pipe and the base of the sink strainer.
  • You should be able to simply release the slip nut by hand by gently twisting it in the opposite direction of the clock.
  • If you are having difficulty, it is possible to pry the slip nut free using a pair of pliers.

Step 2: Remove the Sink Strainer

  • Locknuts are huge hexagonal metal or plastic fasteners that secure your sink strainer to the underside of your sink’s drainboard.
  • Using a set of channel locking pliers, secure the locknut in place for the greatest possible grip.
  • To loosen the locknut, turn it counter-clockwise.
  • Continue to loosen the locknut until it is no longer attached to your sink.
  • After that, just take the strainer by the hand and pull it straight out of the top of your sink.
  • Some strainers are held in place by screws that are visible.
  • Using a screwdriver instead of a hammer will work in this situation.
  • There are several different types of sink strainers, so take your old strainer along with you to the home improvement store so that you can figure out which one to acquire next time.
  • Make an effort to find one that is the same type and size as the previous one in order to reduce the probability of encountering issues.
  • Bell washer sink strainers are distinguished by a huge bell-shaped element that attaches right beneath the sink.
  • Locknut strainers are secured in place by a big threaded nut, which prevents leaks from occurring.
  • Any putty from the previous installation, as well as some muck that has collected across the drain hole, are most likely to be found.
  • Now, you need to take a moist paper towel and carefully wipe the area surrounding the hole to ensure that your desk is free of dirt and debris.

Step 3: Apply Plumber’s Putty

  • Putty is a non-adhesive compound that is used to form a water-tight seal across drains and other plumbing fixtures.
  • Pick up some plumber’s putty and mix it together until it’s simple and easy to deal with, maybe a tablespoon or so.
  • Use your hands to stretch the putty between your palms to form a lengthy rope that is about 1/2 inches thick.
  • Next, you have to apply the plumber’s putty all across the edge of the drain hole.
  • Plumber’s putty is available for purchase at your local hardware shop.

Step 4: Install the New Strainer

  • If the strainer is made up of numerous sections, remove the upper and bottom portions of the strainer.
  • Match the top portion of the strainer with the opening hole and gently press it down into the putty to seal it in the hole.
  • Make an effort to position the drain in the hole so that there is no space between it.
  • It is OK if excess putty pushes out from the edges of the sink strainer during installation.
  • Simply clean it away and toss it in the dust bin.

Step 5: Tighten the Lock Nut

  • Use needle-nose pliers to insert them into the strainer’s aperture from the top and secure them gently in place to prevent the strainer from sliding while you are working.
  • Hand-tighten the locknut by turning it in a clockwise direction.
  • Use a pair of channel-locking pliers to twist the locknut by a quarter turn further and secure it in place.
  • Without holding the sink strainer in position, it will whirl around and fail to properly seal in the moisture.
  • Avoid overtightening your strainer in order to prevent damage to it or your sink.

Step 6: Check for leaks

  • Now, you have to rematch the slip nut on the upright drain pipe with the base of the sink strainer so that it is parallel to the floor.
  • Next, rotating it counter-clockwise will help to snug it against the drain pipe.
  • Continue to tighten the nut by hand until it is firm.
  • Now insert your sink and turn on the water supply from your faucet.
  • Ensure there isn’t any water leaking below your sink.
  • After that, unhook your drain and allow the water to flow out.
  • Ensure there aren’t any leaks in your pipelines.
  • When you still have leaks, have a professional plumber inspect your sink.

Why your Sink Drain Pipe Leaks ?

You’ll certainly be asking yourself what created the leak in the first place once you’ve cleaned up the hot water and dried off your damp possessions.

There are a few factors that might be the source of this type of leaking sink.

Some of the most prevalent reasons for kitchen sink drain pipe leaks are as follows:

1. Clogged P-trap

Clogs in your drain line may increase pressure on the piping system, causing it to fracture and leak. This might be the cause of a sink that isn’t draining properly and appears to be dripping.

2. Incorrect Size of Drain Pipe

I’ve seen a number of strange drain pipes, but they are not the right size for the sink and do not really fit together. If your drain pipelines were the wrong size, then there would be too much stress and water pressure at the connecting point, forcing them to leak.

3. Loose compression nut

One of the most frequent causes of a leaking drain pipe at the junction is a weak compression nut. Quite often, the cause of a leaking drain pipe is just a loose compression nut. Before hiring a plumber, try tightening it yourself if you’re confident in doing this, and see if it solves the problem.

Before hiring a plumbing service, try tightening it yourself if you’re confident in doing this, and see if it solves the problem.
If twisting the compression nut does not stop the leak, it is possible that the nut is fractured or has chipped or worn-down studs. If that’s the case, water may readily escape at the connecting spot, resulting in a sewer pipe leak.

Beginner’s Guide: How to Fix a Leaky Shut Off Valve (3 Quick Steps)

0

What to do if your main shut off valve is leaking ? how to fix it ? I explained them in a detailed manner.

Incase your home has an old gate valve, then that may be the cause of leaking. Outdated Gate valves are very prone to leaking and damage.

so I will suggest you to replace that with a ball valve, since they are very strong compared to gate valves.

repair a leaky shut off valve

But before that, you should try out these DIY fixes, which may help you to solve this problem. I will guide you fix a leaky water shut off valve.

Also read: How to fix a leaky bathtub faucet

Step by Step Guide: How to fix a leaky Shut off valve

1. Fasten the Packing Nut

First off all you want to locate the packing nut in your water shut off valve. Packing nut is used to create a water-tight seal between the stem of the valve and water supply line.

As a result, if there is a spill at the valve stem, it is most likely due to the fact that the valve has not been completely turned.

so what you have to do means, just tighten the packing nut until it is not turnable.

What You Will Need

To complete this process, you need a tool called wrench.

Follow these procedures to tighten the packing nut!

  • Take the wrench and use it to turn the packing nut
  • Look for any leaks.
  • If the leak persists, adjust the packing nut and verify again.

If the leakage continues, proceed to the next option.

2. Packing material should be replaced

What You Will Need

For doing this step, you need the following materials.

  • wrench
  • replacement packing material

As soon as you tighten the packing nut on your primary cut-off valve, it will compress he packing material against the washer.

It will helps to prevent the entry of water.

However, if the packing material solidifies or decomposes over time, it will result in leaks in the water valve.

Now you may ask, how to fix it ?

When this incident occurs, you must change the packaging material as follows:

  • Turn off the water supply to your home from the street. This can be done by rotating the main valve in an anticlockwise direction. you can find this main valve near your meter box.
  • Now, go inside your home and turn on any faucet.
  • Why this is done means, it will helps to release any standing after present in your water line. So don’t forgot to do that!
  • Next step is to remove or take off your shut off valve handle.
  • Once you removed the handle, try to loosen the packing nut.
  • Incase any old packing material is present, use a toothpick to remove that off.
  • Usually these old packing material are made of teflon or some other kind of fibers.
  • There is also chance the rubber gasket may present instead of fibers and teflon.
  • If your valve is like that, then you must remove the rubber gasket as soon as possible.
  • After removing, you will have to apply the new packing material atleast two times around the stem in an anticlockwise direction.
  • In the coming step you have to replace the packing nut.
  • Atlast ensure the materials are properly fitted into the packing nut.
  • Avoid overtightening the packing nut.
  • Restore the water supply and look for any leaks.

If it still drips, then check out the next method.

3. Washer may be the problem

If your shut off valves is still dripping, then there is a chance that you may have a damaged or worn washer. to solve this, you have to replace the washer.

Don’t know how to solve it ?

I will assist you to replace the washer. Follow these methods

  • Take off the valve handle.
  • Using a wrench, loosen the packing nut.
  • Now you have to take off the old packing washer and place the new one.
  • Please keep in mind that the new washer must have the same dimensions as the old one.
  • We recommend removing it and bringing it to a home improvement store or hardware shop to ensure that the replacement is a correct match.
  • Check for leaks.

Incase you still finding leaks at the end of this step means, you must call a professional plumber to inspect your water shutoff valve for damage.

Finally, I also want you to remind that, replacing a leaky gate valve with a ball valve is the most effective solution for this problem.

Video Guide: How to Fix a Main Water Shut Off Valve Leak

Why Your Shut Off Valve is Leaking

Why shut off is leaking

Your main shutoff valve may starts to leak due to infrequent usage. the washer within the main water valve might harden or get coated in mineral reserves over time.

When you shut and reopen the valve, the washer present on the stem of the valve may not seat correctly, producing leakage all around valve thread.

Also read: How to fix a leaky delta faucet

How to Replace a Toilet Shut Off Valve

Step 1: Turn off the Main Water Supply

  • Based on your familiarity with your house, you may have to search for the water main shut off valve.
  • The water supply valve is often positioned in the basement, although it may also be installed in other locations like as the laundry room, below the kitchen sink, or in a storage room.
  • You might have to walk into your yard to find the shut-off valve for the water main.
  • After you’ve located it, switch off the water by tightening the valve.

Step 2: Remove the Standing Water

  • Before removing the toilet shut-off valve, empty the supply line to eliminate any residual water from pouring out into the bathroom floor.
  • Turn on a faucet that is lower than the level of the replacement toilet valve.
  • This procedure permits surplus water to drain from the above-mentioned water pipes, along with the pipeline that delivers water flow to your toilet.

Step 3: Remove the Supply Line

  • The water system to the toilet has a thin flexible tube that connects the toilet to the valves.
  • A small bucket should be placed on the floor beneath the valve to collect any extra water that leaves the line prior to removing it.
  • Loosen the bolt that links the water supply line to the valve with the help of a crescent wrench.
  • After that, remove the pipeline from the valve.

Step 4: Remove the Shut Off Valve

You have to remove the toilet shut off valve based on the type of joints and plumbing fixture you have!

Incase you have compression joints, then the first step is to loosen the bolt.

  • For doing that you need a tool called crescent wrench.
  • Using that loosen the bolt which is joining the pipeline to your current valve.
  • It is recommended to use a pair of pliers to hold the pipe while you are removing the bolt.
  • This will help to keep the pipe from twisting or bending while you give pressure to remove the bolt.
  • After you have taken the nut, remove the old valve out of the pipe with your fingers.
  • Finally, unscrew the nut and compression rings and keep them apart.

If your toilet valve has a sweated copper joints, then you have to lay a tube cutter well above the copper pipe as near to the existing valve as you possibly can.

It is necessary to leave adequate pipe protruding from the wall to allow for the installation of the new valve.

Disconnect the valve by tightening the pipe cutter and rotating till it cuts fully through the material.

Step 5: Replace the New Valve

  • Incase you are attaching the new shut off valve to a copper pipeline, you must use a deburring tool to smoothen the sharp edge that was generated while you are cutting the material.
  • Press the tool securely into the pipeline and spin it a few times until the tip is perfectly smooth.
  • If you’re dealing with a PVC pipe, you may skip this step.

Step 6: Attach the Compression Nut

  • Now you have to attach the compression nut into the copper pipe.
  • During this process, ensure that the threads are pointing towards you.
  • Next step is to press the compression ring onto the tube with your fingers.
  • Move the new valve well above the pipe until it reaches the limit, making sure that the valve‘s outlet is appropriately directed upward to take the toilet’s supply line.
  • Adjust the compression nut to fit the threading of the replacement valve‘s inlet.
  • Next, using two crescent wrenches, first one is to support the valve body in position and the other one is to secure the nut, screw the nut further to 1⁄2 turn with the valve body in point.

Step 7: Tighten the Nut

  • Plug the toilet supply line to a fresh shut-off valve using the provided connectors.
  • If indeed the main line is equipped with a compression nut, you may remove the nut that came with the new or replacement valve when installing it.
  • Attach the bolt to the valve outlet by threading it on.
  • Next, using your hand, tighten the nut.
  • After that, take the crescent wrench to give it a further 1/2 turn.

Step 8: Look for Leaks

  • Now you have to unlock the main water line.
  • Next step is to adjust the toilet shut-off valve by rotating it in an anticlockwise direction.
  • Allow the water to fill the toilet’s tank. Then look for any water leak.
  • Turn off the water, drain the lines, and remove the compression nut from the valve if you find any leaks with it.
  • Apply plumber’s tape or plumber’s putty to the valve‘s studs to seal them.
  • Replace the fitting, ensuring careful to tighten all of the compression nuts, and inspect it again.

Also read: How to fix a leaky shower faucet

Conclusion

Replacement of a leaking valve is a simple repair that most do-it-yourselfers can do in a few hrs.

It is possible to guarantee that your plumbing repair will be a success by following these easy procedures.

This will enable you to stop the leak and put your toilet back into function without any problems at all.

You can do the PVC and copper repairs on your own, but you’ll need to hire a plumber for the older materials.

Best Guide: How to Fix a Leaky Delta Faucet (7 Steps)

0

Do you have delta faucet in your home ? If it leaks, then it will be a major problem for your kitchen.

so, how to fix a leaky delta faucet ?

There will be a moment when your Delta faucet may leak, but it is unlikely that you will have to handle with a leak right away.

However, hiring a professional to repair it for you may be extremely expensive.

However, did you guys know that there are certain remedies you can make yourself to cope with it that will not cost too much ?

First and first, you must identify the model number of the leaky Delta faucet in issue. In the case of components, Delta provides a lifetime guarantee, and they’ll promptly ship you whatever you need. The kitchen faucet may then be disassembled using a wrench, and the seats and hinges can be replaced to resolve the issue.

Continue reading to discover how to work with leaky or dripping Delta faucets even if you have turned off the kitchen faucet fully.

Learn about the most prevalent causes of it and what you can do to cope with it by reading this article now.

Also read: How to fix a leaky shower faucet

Materials required

Fix a Dripping Delta Faucet

If your kitchen faucet drips when you turn it off or leaks through the bottom, this article will walk you through the procedures of fixing it step-by-step.

Note that this lesson applies to both normal Delta faucets and the pull-out variant. 

This DIY Project needs the help of following materials. If don’t have, then buy from any home improvement stores or order in online.

  • Tool kit for Delta with stainless steel ball
  • screwdriver
  • strap wrench, channel lock wrench, or some other kind of wrench
  • silicone paste (optional)

Step by Step Guide: How to Fix a Leaky Delta Faucet

How to fix a leaky Delta Faucet

Step 1: Shut off the Valve

  • Whenever you are doing a plumbing work, be sure to switch off all water sources before beginning.
  • Find the water shutoff valve for the sink.
  • Typically, the valve is positioned below the kitchen sink.
  • The water should be turned off throughout the house or building if there isn’t a separate valve for the washbasin.
  • To shut off the valves, spin the handle, until the lever is perpendicular to the pipeline.
  • Make certain that both the hot and cold water are turned off.

Step : Protect the Drain

  • Remove any water that has accumulated in the leaky faucet or sprayer tip by turning the faucet on.
  • Protect the drain and the garbage disposal (if appropriate) with a cloth or a drain stopper to keep the water from flowing down the drain.
  • It stops bolts from becoming dislodged and washing down the sink drain.

Step 3: Remove the Screw

  • Disconnect the blue and red cover that is positioned on the tap handle using a flathead screwdriver to show the screw that holds the handle in position.
  • Put the cover to one side in a container that will hold all of the screws and other items that will be used.
  • Release the screw that is hidden within the handle. Set it aside for the time being.

Step 4: Remove the Handle

  • Take off the faucet handle from the sink’s bottom.
  • The handle cap may be removed by rotating it counterclockwise, until it comes off.
  • Put it on the shelf for now.
  • If removing the handle cap is being tough, using a hair dryer focused at the handle cap for a couple of minutes could help to solve this issue.

Step 5: Remove the Other Parts

  • Unscrew cam and casing as well as the ball assembly from the unit.
  • Leave them aside for the time being.
  • Take the two pairs of valve seat and springs that are positioned at the head of the sink faucet using a screw driver or other appropriate tools.
  • Kindly ignore the final hole on the base.

Step 6: Install New Parts

  • Assemble the new valve seat and spring.
  • Replacing them into the openings will ensure that the rubber will be level with the metal hole.
  • There must be a perfect flat fit between the springs and the metal, otherwise the ball assembly would not have enough space to move.
  • Put the ball in the kitchen sink so that the openings in the ball’s pores line up with the openings in the pipelines that holds the faucet.
  • Put the cam and packing on head of the ball.
  • Make sure the little plastic clip aligns with the tiny metal notch at the the 9 o’clock position in the faucet pipeline 

Step 7: Replace the Faucet Parts

  • Before restoring the ball assembly, apply silicone paste to the ball and allow it to dry.
  • The silicone paste prevents the handle from shifting too much during use. (Optional Step)
  • Using your fingers, keep the cam and packing in position while screwing the cap assembly back into position.
  • Reattach the sink lever at the head of the ball assembly.
  • Reinstall the handle by screwing it in position.
  • Now you have to reattach the red and blue cover.
  • Then, move the water valve up to its on position, making sure that the knobs are parallel with the pipeline.

Wow, you have successfully repaired your sink!

Also read: How to fix a leaky bathtub faucet

Video Guide: How to Fix a Dripping Delta Faucet

How to fix a leaky ball type faucet

How to fix a leaky ball type faucet

A leaking faucet is one of the most prevalent types of home plumbing repairs.

Although, because to the large range of faucet models that may be found in the house, this simple repair might seem to be a difficult task.

As an instance, a single-handle tap might be either a ball-type faucet, a cartridge faucet, or a disc faucet, and the fixes for each of these types are rather different, despite the fact that they seem to be fairly similar from the exterior.

Every faucet style may also vary from one producer to another, depending on the brand.

Step by Step Guide: Fixing a Leaky Ball Type Faucet

Step 1

  • Switch off the water flow to the leaky faucet by turning the knob to the left.
  • Most of the time, the shut-off valves for the hot and cold water will be positioned beneath the sink.
  • In the unlikely event that you are unable to locate the outlet shut-off valves, you will be forced to switch off the primary shut-off valve that controls water supply throughout the whole home.
  •  After you’ve turned off the water flow , switch on the faucet to ensure the water is completely turned off and/or to remove any leftover water that may have collected.

Step 2

  •  Rotating the set screw counter-clockwise with the Allen wrench which comes with the repair kit (or another of appropriate size) will free the handle and allow it to be removed.
  • Disconnect the single lever handle from the frame.
  • The faucet head cap will be exposed as a result of this action.
  • Incase your faucet was spilling from the bottom of the faucet nozzle, then you have to fasten the locking neck of the faucet nozzle by twisting it clockwise with the specific spanner wrench.
  • Then, look for leaks. If the leak has stopped, replace the dripping faucet handle.
  • Following this, if the leak remains, then try out further steps.

Step 3

  • To unscrew the top cover, grasp it with channel-lock pliers and twist it counter-clockwise to release it from the screw.
  • It is possible to avoid damage to the cap surface by covering masking tape across the upper and lower jaws of the pliers.
  • The cam will become visible when the top cover has been removed.
  • This is the piece of material with the handle protruding from the center of it.
  • Separate the cam, cam washer, and ball assembly from the unit.

Step 4

  • Once the control ball has been removed, it should be checked for damage.
  • If the ball has been netted or cracked, it must be replaced as part of the fix.
  • It is possible to utilize either a plastic or a metal ball.
  • Slip down into the faucet body with a tiny flat-blade screwdriver and pry off the seals and springs from the holes at the base of the faucet body, as shown.
  • It’s imperative to pay close attention to how well the hinges are orientated within the rubber seals.
  • Most of the time, the springs are placed such that the thin end of the springs points downwards into the rubber seal.

Step 5

  • Disconnect the faucet spout by raising it upwards and turning it off; this may take a little amount of force to be completely removed.
  • Take off the O-ring that surrounds the bottom of the faucet body by pulling it out from behind using a screwdriver or gently cutting it out with a utility knife, as directed.
  • Take better care not to damage the faucet‘s body while turning it on.

Step 6

  • Next, you should coat the new O-ring with the heatproof plumber’s grease provided with the repair kit.
  • It is advisable to place the new O-ring on the base of the faucet and then slide it back and forth around its body till it settles in a groove neatly.

Step 7

  • Reconnect the faucet spout to the faucet bottom by pushing it back above the O-ring till it is completely placed on the bottom.
  • Attach the new seals and springs by inserting a spring through every rubber seal and lowering the whole assembly into the hole located at the base of the faucet body (see illustration).
  • It’s possible that you’ll have to push them into a position using the edge of the screwdriver.

Step 8

  • Insert the new control ball by matching the notch on the ball with the opening in the faucet housing and tightening the control ball.
  • In order to finish, position the cam washer on top of the ball and lever, and then insert the cam.
  • The cam is often equipped with an adjustment lug that is designed to fit into a slot in the faucet body.
  • Insert the cam in its proper position by pressing it all the way in.  
  • Using channel-lock pliers, attach the top cover onto the faucet body and tighten it, until it is secure.
  • Please avoid over-adjusting the faucet, as this may lead the ball to clump and get stuck inside the dripping faucet.

Step 9

  • The single lever handle should be fastened above the ball’s stem, and the Allen screw should be tightened to hold it in place.
  • Switch on the water system and water supply line and then inspect the faucet to see if there are any drips or leaks.
  • The most typical reasons for leaking are that the valve seals are not correctly placed in the openings, or that the top cover is not fitted correctly.

Also read: How to fix a leaky outdoor faucet

Why your ball type faucets are leaking ?

  • Most of the time a faucet may leak due to wear and tear of internal components
  • For faucets that are leaking from the base of the faucet spout, may have a worn out O-ring. 
  • Incase your faucet is dripping water from the edge of the spout, then your faucet may have a damaged rubber seals or springs or control ball.
  • This issue can also be caused, if the water flow is not regulated by the lever ball.
  • To identify the origin of the leak, you’ll need to unscrew the faucet (a relatively easy process) and physically check the pieces.
  • For convenience, you may opt to change all components rather than identifying the precise cause why and how the sink faucet is dripping.

Conclusion

Delta is one of the greatest faucet brands available because of the amazing quality of customer service that they offer.

It’s also worth noting that they provide a lifetime guarantee on all components as far as you’re the real owner, which makes it considerably simpler to handle fixes on your own.

These solutions would normally be quite expensive, but learning the fundamental repair techniques that you can perform will and you save a lot of time and money.

You should keep in mind that fixing a Delta faucet leak will not cost you much and will not take long at all.

Best Guide: How to Fix a Leaky Shower Faucet (7 Easy Steps)

0

A leaky shower faucet may be both inconvenient and expensive, since it will almost definitely result in increased water bills as a result of the leak.

The good news is that you can repair your dripping shower faucet them self with a few simple tools and supplies.

So how to fix a leaky shower faucet?

Incase you have a leaky single-handle shower faucet, you need to replace the cartridge in your shower faucet. Suppose you have a 2 handle shower faucet, then you need to replace the washer in the handle of the shower faucet If your do-it-yourself repair doesn’t work, you might have to hire a professional plumber for assistance.

The below step by step guide will helps to understand how to fix a dripping shower faucet.

Also read: How to fix a leaky outdoor faucet

Why is my shower faucets and shower head is leaking ?

Why is my shower faucet is leaking

Before learning how to repair a dripping faucet, it is important to understand that the leak is caused by damaged shower faucets or valves.

Mineral deposits may have harmed or obstructed the inner function of certain parts.

Furthermore, they may include components that are completely old and worn out.

Since there are so many different types of faucets available for purchase, there is no universal procedure for repairing damaged faucets.

In order to make things as simple as possible for you, we’ve put together this post that will walk you through the process of repairing leaking shower faucets of various sorts.

Also read: How to fix a leaky bathtub faucet

How to fix a leaky shower faucet with single handle

How to fix a leaky shower faucet

How to fix a leaky faucet which won’t turn off properly. The majority of single-handle, cartridge-style faucets may be fixed in an hour or less using simple hand tools.

Change the old cartridge with a new cartridge that is similar to the previous one to repair a leaky shower head.

In this post, we’ll go through how to replace the cartridge faucet, which is a common problem.

Cartridge valves are activated by sliding the cartridge in and out of the valve stem, which is controlled by a single handle.

In the following phases, you will understand more about how to change the cartridge in your dripping shower faucet.

Step 1: Turn off the Shower’s Water Supply

  • The shower’s water supply should be switched off.
  •  Then, using a tiny pocketknife, pull off the handle cover to show the inner handle screw, which may be removed.
  • Disconnect the handle screw by loosening it and pulling it out.

Step 2: Remove the Handle

  • Remove the faucet handle and store it safely.
  • Switch off the water at the cutoff valves for the fittings or at the control valve for your house.
  • Check the status of a faucet by turning it on and off.
  • Then, you should remove the handle, from the body.
  • If the handle continues to cling, consider steaming it with a hair drier.
  • When you still can’t get that off, try using a special handle puller, which is a low-cost instrument that can be purchased from plumbing parts wholesalers or home improvement stores.

Step 3: Pull the Cartridge Clip

  • Remove the stop tube by pulling it out.
  • Using a little screwdriver or awl, pull the cartridge holding clip out of the way.
  • Release the handle washer, next turn the cartridge stem free using pliers and take this out with the pliers to complete the removal.
  • If it becomes jammed, a special cartridge puller must be used.

Step 4: Remove the Hex Screw

  • Remove the hex screw and hex nut from their positions till the threads are exposed.
  • Insert the puller above the cartridge stem, making sure that the tool ears are aligned with the cartridge slots, and then twist to free the cartridge stem.
  • In terms of attaching the cartridge to the faucet assembly, almost every faucet producer employs a different technique.
  • Check for and remove any clips or springs that you may have.

Step 5: Take off the Cartridge

  • Cartridges have a reputation for being difficult to remove from their holders.
  • New cartridges from certain manufacturers come with a cap that may be removed.
  • Place the cap with the old cartridge ears and attempt to spin the cartridge out of the case.
  • Then, using pliers, pry it out of the way.

Step 6: Remove the Old Cartridge

  • If you are unable to remove the old cartridge, you will want to use a cartridge puller.
  • Make certain that the one you choose is compatible with your particular brand of faucet.
  • Check for the company or manufacturer’s name on the handle or rim of the faucet.
  • Someone who is skilled with plumbing components could be able to determine the brand and model from a photograph.

Step 7: Tighten the Hex Nut

  • When you remove the cartridge, be sure you wiggle it free from the slot.
  • Take the old unit with you to a plumbing supply shop or a home improvement center to ensure that you get an identical replacement cartridge.
  • Hand-tighten the hex screw until it reaches its lowest point.
  • Tighten the hex nut with one hand while pulling on the cartridge puller handle with the other.
  • Keeping the puller handle firm while tightening the hex nut 2 full revolutions can help to remove the cartridge if it would not come out.
  • By taking the cartridge out of the faucet body, you could remove it.
  • Purchase a new cartridge that is similar to the original, position it appropriately, and reassemble the pieces.

Also read: How to protect outdoor faucets from freezing

How to fix a leaky shower faucet with two handle

 

The layout of the shower valve has an impact on this portion of the job.

Step 1: Remove the Cap

  • ancient or simple faucets often have a visible screw in the center that can be seen from a distance. They may also have a screw on the tip of the fitting to secure it in place.
  • If you have a decorative or contemporary shower bathtub faucet, you will need to acquire a cover cap that conceals a screw in order to use it.
  • When you find it, remove the cap to expose the screw below.
  • Use a small screwdriver or pocket to pry apart a faucet cover cap that seems to be fixed in the faucet body.
  • Prevent snatching the material’s surface when working with it.

Step 2: Remove the Locking Screw

  • Remove  the locking screw below the cover cap.
  • Make use of a screwdriver to spin the screw in a counterclockwise direction.
  • As soon as it comes off, store it in a secure location.

Step 3: Take off the Handle

  • Disconnect the handle by twisting and dragging it away from the body.
  • If this component seems to be locked, a screwdriver or faucet puller may be used to free it.
  • Next, clean the trim and cover on the faucet stem with a soft cloth.
  • Remove the faucet stem using a deep socket.

Step 4:  Unscrew the Stem

  • Position the tool on the stem’s nut and spin it in an anticlockwise direction to loosen it.
  • Make certain that you apply enough lubricant to get the nut to move.
  • After it has been taken away, unscrew the stem and pull it away from the valve body.

Step 5: Reassemble the Stem

  • Reassemble the stem by reattaching all of the individual pieces.
  • All of the faucet washers, O-rings, and the flat washer are included in this category.
  • It is important to note to loosen the screw before installing the new washer.

Step 6: Replace the Faucet Stem

  • Replacing the faucet stem with the valve body is performed by repeating the steps 3–1. 
  • Plumber’s grease should be used to lubricate the sequential grooves on both components before connecting them together.
  • Reconnect the handle (partially) and turn on the water to check the valve when the stem has been screwed down into the body of the valve.
  • When there is no leak, tighten the handle and seal the trim to the wall using tub caulk to complete the repair.

Also read: How to remove calcium buildup on faucets

How to fix a leaky shower head

How to fix a leaky shower head

Step 1: Turn off the water supply.

  • Turn off the water main that supplies the whole home.
  • Keep a towel nearby because even though your water main may have been switched off, there might still be water remaining in the pipeline that would leak out.

Step 2: Check the Washer

  • Disconnect the leaky shower head from the pipeline by loosening that with your hands from the pipeline.
  • Using pliers or a curved wrench, loosen the head if it is held on tightly.
  •   Check within the showerhead’s threads for a little plastic washer or a rubber O-ring .
  • Due to the excessive wear that occurs with ageing on this part that causes a showerhead to leak and begin spilling.
  • Throughout time, it wears out and becomes fragile, which reduces its capacity to retain water in the first place.
  • If it seems to be damaged or teared, it should be replaced.

Step 3: Clean the showerhead 

  • It’s a smart idea to clean out the showerhead while you’re doing this, particularly if you’ve been experiencing low water pressure in the shower.
  • The inside of the showerhead or the stem of the pipe may often be found to have mineral deposits or silt left behind by hard water, which should be cleaned out.
  • This may have a considerable impact on flow rate and pressure, and it can also lead to a leaking showerhead in certain cases.

Step 4: Vinegar Solution

  • Stir 3 tablespoons of vinegar and 3 glasses of water and boil in a small frying pot or skillet, stirring constantly.
  • Once the water has begun to boil, remove it from the fire.
  • If the showerhead has any rubber part, then you should remove it.
  • After removing, put the showerhead inside the solution and allow it to rest for roughly 20 to 30 minutes.
  • Next, using an old toothbrush, remove any sediments from the inner and outside nozzles and wash them clean.
  • Repeat this process until no sediments are left.

Step 4: Secure it With Tape

  • If somehow the washer or O-ring seems to be in good condition or has been changed, the very next method is to roll Teflon tape over the threads on the pipeline stem.
  • Don’t go excessive with the tape.
  • At the very end of the pipeline stem, tie a small strip all around threads to secure it.

Step 5: Reattach the Showerhead

  • Replace the showerhead by arm tightening it until it is no longer turnable.
  • Then, using pliers, give it one more turn to secure it.
  • Keep in mind that if you spin too forcefully, you might shatter the showerhead or the tube.

Step 6: Check for leaks

  • Restart the water supply and then take a quick shower for a couple of seconds.
  • Switch it off if it’s on. 
  •  Simply wait for several minutes, and then verify to see if the leak has been fixed or not.

Tips to consider while fixing a leaky shower faucet

Use these instructions to deal with any further difficulties you may have with your connections, with the exception of your shower filter.

If you’re following the directions on how to repair a leaking shower head, you should protect the bathtub or shower surface with rags. Keep in mind to cover the drain to avoid small pieces from falling into the sink.

Once you begin to work on a leaking valve, turn off the water supply to your restroom to prevent leaks. If you are unable to locate the valves for the shower, you should turn off the whole water system to the entire house. Now, by turning on the bathroom sink valve, you may drain the water from the pipelines.

Avoid overtightening the faucet if your locked shower head continues to drop water despite your efforts. This activity has the potential to harm the valve, which might result in additional complications.

Make use of as little time as possible during your rebuild task because your house may require the use of water for a variety of purposes.

Video Guide: How to Fix a Leaky Shower Faucet

Conclusion

In addition to causing high power bills, dripping faucets and shower heads may also cause serious damage to bathroom walls and other materials.

Therefore, learning how to repair a faucet using the numerous techniques outlined in this tutorial can help you prevent similar problems in the future.

Best Guide: How to Fix a Leaky Outdoor Faucet (9 Steps)

0

It may not seem like a big concern if your outdoor faucet is leaking. There is an issue elsewhere, and the spigot is going to be wet anyhow, so what’s the big deal?

Even though a leaking faucet may not cause harm to your home, it will waste a significant amount of water. Additionally, a gradually leaking faucet may not always remain in this state.

It has the potential to become a larger leak, which might cause damage to neighboring plants. This blog post explains how to fix a leaky outdoor faucet while conserving water.

With the growing cost of water, a leaking outside faucet has become more than just a minor inconvenience. Even the smallest amount of water accumulates over time, resulting in a significant rise in your monthly expenses.

However, a dripping faucet may do more than simply drain your water flow. A gradual drop adjacent to your home’s foundation may ultimately enable water to seep into minor fractures in concrete and brick, causing water damage.

As soon as this occurs, you will be faced with an even more difficult situation if the faucet is not repaired as soon as possible.

Let’s see how to repair a dripping outdoor faucet in your yard.

Also read: How to fix a leaky bathtub faucet

How to fix a leaky shower faucet

Step by Step Guide: How to Fix a Leaky Outdoor Faucet

How to fix a leaky outdoor faucet

Step 1: Examine the Packing Nut

  •  A packing nut is located behind the handle, and it is responsible for keeping the water’s outflow blocked off externally.
  • A leaking outdoor faucet repair begins with the adjustment of this packing nut, which should be done with a 1/2-to-1/8-turn torque.

Step 2: Clam the Seal

  • If you have a screw in the middle of your handle as opposed to a screw on the outside, apply the same methods as you would for the screw.
  • Usually, just clamping this seal is all that is required to restore successful function to your hose bib system.
  • If you discover that your outside spigots are still dripping after doing this procedure, you will need to proceed with extracting this packing nut fully in order to have entry to the faucet valve stem.
  • Ensure that your water supply has been shut off before you proceed.

Step 3: Shut Off your Water Supply Valve

  • Whenever you are working on a hose repair, it is essential that you switch off the water supply first; otherwise, you may encounter all kinds of complications when you attempt to unscrew the packing nut in order to get access to the spigot stem.
  • Since a starting point, if you’re not sure where to start, we suggest looking for your water meter initially, as you’ll often locate your water shut-off valve next to it.
  • The position of the control valve and the water meter varies depending on the temperature, with interior water meters being more prevalent in colder areas and outdoor water meters being more popular in hotter areas.
  • Exploring your underground, workshop, or crawl space may provide results if you suspect your water meter is placed inside.

Step 4: Rotate the Handle

  • Water shut-off valves are typically activated by rotating them clockwise to horizontal, which shuts off the supply of water.
  • If your valve has a handle, twist it clockwise till you are unable to twist it any further.
  • Once you’ve completed this step, be sure to switch your outside faucet to the open position before continuing with the repair.
  • This is done in order to drain any extra water that may have accumulated in the pipelines.

Step 5: Unscrew the Packing Nut

  • As soon as you are certain that the water supply has been turned off, just use an adjustable wrench to unscrew the packing nut that is located beneath the faucet’s handle.
  • Removing the handle will give you the opportunity to reach the washer assembly, which will almost certainly need replacement.
  • This step will be somewhat different based on whether you are dealing with a standard or frost-free faucet.
  • If you have a standard outdoor spigot, the washer assembly will be located just beneath the faucet handle.
  • A freeze-proof faucet’s handle is linked to a lengthy metal rod known as the faucet stem, which is what you’ll see if you use one.
  • Disconnect the whole stem, and you’ll discover the damaged packing washer on the other end of the stem from where the handle is located.

Step 6: Remove the Assembly

  • Loosen the washer assembly with a screwdriver, allowing passage to the washer to be reached.
  • Replacement of the torn washer with a spare one that has the same shape and dimensions as the torn one.

Step 7: Replace the Handle

  • Reinstall the screw that is located at the very end of the spigot stem or tap handle.
  • Restore the handle to its original position and secure the packing nut by rotating it in a clockwise direction.

Step 8: Check the Vacuum Breaker

  • If you live in a modern home, it’s possible that you’ll be dealing with a frost-free faucet.
  • In that they protect pipelines from freezing and breaking, these valves are also more complicated to install and maintain, which means there are more areas where your leakage might be occurring from.
  • Vacuum breakers are notorious for having a valve that wears out and breaks, allowing water to get through when it would not ordinarily do so.
  • However, you will most likely need to bring your old vacuum breaker to a home improvement store to ensure that the new component is a perfect match for your specific spigot before you can proceed.

Step 9: Replace the Vacuum Breaker

  • Simply remove (or take off) the vacuum breaker cap that is located on the head of your faucet before leaving the house for the shop.
  • The vacuum breaker is located under the surface.
  • When it comes to removing this component, each faucet is unique, but in general, you will be able to do so by simply loosening it to free it from any threads or dragging it out with pliers.
  • In the same manner that you took the previous one , you’ll want to replace it with the new.

Video Guide: How to Repair a Leaky Outdoor Faucet

What are the causes of a leaky outdoor faucet?

Causes of leaky frost-free faucet

Before you can start fixing a leaking outside faucet, you must first determine the source of the issue. A leaking outdoor faucet might be caused by numerous factors.

If your exterior faucet drips from the spout after the water is shut off, the washer is most likely the culprit and should be fixed or changed.

If the water spigot is seeping from the handle when it is switched on, the stem sealing may be the cause of the problem.

Outdoor spigot spills are frequently caused by worn-out washers.

Additional reasons for outdoor faucet failures include broken, frozen, or obstructed pipelines, in addition to wear and strain on the washers and packing surrounding the handles.

Tubes may get blocked with mineral reserves and other debris over time.

Frost injury to a pipe happens when the moisture in the pipeline freezes, causing the material to stretch and shrink, eventually breaking the pipe.

That’s why, while winterizing your house in the autumn, it’s critical to turn off outdoor faucets.

If the leaky garden faucet is extremely old, it may be more cost effective to just change it rather than waste time and money repairing it.

Also read: How to protect outdoor faucet from freezing

What is the cost of repairing a leaky faucet

Leaking frost-free faucet

  • If you’re simply twisting or changing a loose washer, repairing a leaking outdoor faucet may be done for very little or no money at all.
  • If, on the other hand, you decide to replace the complete outside faucet, the expense of changing each component might quickly mount up.
  • In most cases, changing a spigot will cost about $90-$100, whereas a new metal hose bib with a cutoff valve would cost around $150 to $200.
  • Depending on the situation, the cost of repairing or changing an outside faucet might vary between $50 and $300.
  • A garden hose bib costs between $5 and $10 on its own, so if you’re doing it manually, you’ll probably save a significant amount of money.

Also read: How to remove calcium buildup on faucets

How to replace a outdoor spigot

1. Find the water shutoff valve and flip it clockwise to switch off your water system. Locate the outside spigot and replace it as described above.

2. Open the outside spigot to drain any residual water from the tube.

3. To unscrew the leaky spigot, twist it in the opposite direction to the clock.

4. Take a firm grasp on the tube and spigot, and then pry them out.

5. Remove the threads with your solid brush, as shown in step

6. Apply plumber’s tape to the threads of the pipeline to hold them in place.

7. Insert the new spigot and tighten it with a wrench to ensure that it is firmly in position.

8. Now, switch on the water flow and inspect it for any lingering leaks.

If a water leak occurs as a result of breaks in the pipe caused by frost damage, it is best to call an expert rather than attempt the repair yourself, unless you have extensive expertise in working with plumbing issues.

Also read: How to remove faucet stem

Conclusion

Our blog post has shown you some of the more common reasons why you may have a leaky outdoor faucet. Hopefully, now you can figure out how to fix the leaky faucet all on your own.

Regarding Questions

Why is my frost free spigot leaking?

Whenever your faucet drips out of the nozzle when it’s switched off, the washer is damaged.

On frost-proof faucets, the washer is situated on the tip of the faucet stem.

If you discover that the faucet begins dripping again after a matter of seconds, the valve seat is damaged and you must change the complete frost-proof faucet.

How do you secure an outside spigot?

It’s simple and inexpensive to lock your outdoor water faucet using a faucet lock, which is offered at hardware shops. These closures come with keys or a clasp system, to turn them on and off.

You may also attach a flow meter to detect water loss or turn off the primary outdoor spigot valve.

What is the cap on top of an outdoor faucet?

The vacuum cap is round and approximately an inch wide, and it either slides or threads onto the head of the faucet. The component below is referred to as a vacuum breaker or perhaps an anti-siphon valve.