How to Install Undermount Sink Without Clips !
Do you lack the necessary clamps or mounting clips to keep your sink in place?
Are you scared about installing a sink that does not have mounting clips?
Do not be concerned! Without the use of clips or other mounting gear, it is feasible to install an Undermount sink. If you cannot install your sink because you may lack the necessary pins, If this is your problem then don’t worry!
In such a scenario, you may use silicone glue and epoxy to attach the sink to the countertop of your kitchen cabinetry. The following are the procedures to follow to install an Undermount sink in your kitchen without the use of clips or brackets.
How to Install Undermount Sink Without Clips : Step by Step
Let’s see the step by step process to install undermount sink without clips .
1. Cleaning
When installing your kitchen sink with adhesive, it is essential to clean both the countertop surface and the sink surface that will come into touch with each other during the installation process.
Cleaning your surfaces with acetone and a clean cloth eliminates any filth, dirt, oil, and other contaminants that may impede the cleaning process. Whenever you are using this product, you must adhere to all of the directions and precautions stated on the acetone bottle. Immediately after cleaning, let the sink surfaces dry completely, which typically takes just a few minutes.
2. Apply Adhesive
When purchasing an adhesive, it is important to use the finest glue available so that your sink will remain precisely aligned with the countertop for an extended period of time.
Although many readily accessible adhesives on the market are also appropriate for kitchen sink installation, clear or crystalline silicon is considered as the industry standard. It is superior to other kinds of adhesives in terms of strength, and it is also used to seal the area surrounding your Undermount sink once it has been installed.
In order for the sink and the countertop to connect, the sink must have a contact surface.
When your sink makes touch with your countertop, this is referred to as the “contact surface.” A silicone bead or cord is wrapped around the contact surface of your sink.
For an under-mount sink, the contact surface is typically a 1-inch lip on the same side of the sinkholes as the sink openings themselves. Drop-in sinks require silicone to the bottom of the sink’s perimeter, which is the opposite side of the sinkholes.
also read : How to Clean granite Sink and Granite Composite Sink
3. Installation
You must install the sink at the bottom of the countertop if you wish to use an under-mount sink installation method.
Before applying the glue, the installers must first put the sink in the cabinet under the aperture for the sink. Next, your sink is lifted until it makes contact with the bottom of your countertop after the silicone glue has been applied.
Depending on the number of drain holes in your sink, 1-2 bar clamps and a cross bracing will be required to secure it in place. One end of the bar clamp is attached to the bottom of your sink via the hole for your sink drain, and the other end is secured to the cross-bracing of your sink.
Next, the installer adjusts the location of your sink and tightens the bar clamps until your sink is flush with the surface of your counter. The clamps will stay in place until your silicone has hardened completely.
Drop-in sinks are more easily installed than their under-mount counterparts because they are more accessible. Next, the adhesive is applied beneath the lip of your sink, which is then lowered into place and adjusted to its proper position.
4. Washing
Both drop-in and Undermount sinks need immediate cleaning following installation to remove any excess silicone from the sides of the sink.
You have to eliminate the extra sink edges and debris from the surface of them. A tiny amount of silicone oozes out from below the sink edges when you tighten the clamps.
Before removing the extra silicone, connect the sink lip with the surface with your finger to make sure that they adjust correctly. If you believe you need to apply more silicone, go ahead and do so, removing any excess silicone with a cloth and acetone before it hardens.
After you have cleaned the surface of your sink, it will seem flawless, clean, and glossy.
Also read : How to Install utility sink next to washer
5. Epoxy
The last step in installing an Undermount sink without hardware is to provide additional support for sinks that have a trash disposal system.
Filling your sink with water may put a tremendous amount of pressure on the trash disposal sides, causing your sink to come loose from the countertop. Adding extra support to your sink will decrease the likelihood that it will get dislodged from its countertop. –
The expert installers will connect tiny pieces of granite or acrylic material to the underside of your countertop using two-part epoxy. It will help to overlaps the lip around your sink. Because your epoxy is a highly fast-setting substance, it also enables the installer to join the piping immediately after your sink installation, which would not have been feasible if you had used your silicone instead.
Using your epoxy and blocks with a drop-in sink is not essential since the countertop supports the sink.
Conclusion
We hope you enjoyed this blog post about how to install an undermount sink without clips. By following the list of instructions provided you will be able to install a beautiful new sink without needing to pay a professional to do it for you. If you have any further questions about installing a sink please feel free to contact us anytime. Thank you again for reading, we are always excited when one of our posts is able to provide useful information on a topic like this!
FAQ
about how to install undermount sink without clips
1. Do undermount sinks need clips?
You may install Undermount sinks in a variety of ways. The majority of ways are acceptable. However, the manner utilized is usually determined by how the installer was taught to perform it. For example, some installers prefer to use clips or brackets, while others prefer to use glue.
2. Do you install undermount sink before countertop?
Before laying down the countertop slabs, installing an Undermount kitchen sink in the space available is essential. You will not be able to fit the sink through the hole after the countertop slabs have been installed, and you will not be able to properly seal the gap between the sink and the bottom of the countertop once it is installed.
3. Does silicone hold sink in place?
Silicone caulking is used to seal the sinks to the countertops and to keep water out of the sinks. For sink installation, a particular kind of silicone caulking compound is available that is designed especially for this purpose.
