How to Disconnect Sprayer Hose from Delta Faucet: 5 Best Steps

How to Disconnect Sprayer Hose from Delta Faucet

As it is evident to everyone who has seen or heard of Delta faucets, the brand has some of the biggest and most popular bathroom faucets on the market right now. A distinctive feature of Delta kitchen faucets is their retractable sprayer hoses.

When sprayer hoses are present, their presence can cause some issues for one or more of the following reasons.

At times, one of the sprayers or the faucet may malfunction, and only one of them will deliver water. You could also notice leaks in the sprayer hose, which means you need to replace the hose.

If you are planning on replacing the sink, you may opt for a new faucet connect that does not have the sprayer hose.

How to Disconnect Sprayer Hose from delta faucet

This article states in detail how to remove the sprayer hose from your Delta faucet on your own so that you will know exactly how it is done.

The faucet-sprayer system is so simple once you understand how it works, so that you can quickly disconnect the sprayer hose from the delta faucet.

Here is how the spray hose is connected to the faucet, so you can grasp the process more easily.

Must Read

Where are kraus Sinks made

How to Install a Farmhouse Sink

How to Clean Sink Grid

How to Wash Dishes in a Farmhouse Sink

Best Methods to Remove Faucet Without Basin Wrench

How to Remove Faucet Handle Without Screws

How to Tighten Kitchen Faucet at Home in 6 Steps

How to Vent a Kitchen Sink under Window

Top 10 Best Pullout Kitchen Faucets in 2o21

Fireclay vs Cast iron sink

How the Sprayer head and Faucet Works ?

How to Disconnect Sprayer Hose from delta faucet

Water is delivered to your faucet via supply lines under your kitchen sink. As you examine a bit closer, it becomes clear that the faucet and the sprayer are connected by a tube or hose.

As it turns out, a small, hard-to-see fixture, commonly called a diverter, is located inside the faucet, and its role is to direct the water from the faucet to the sprayer head. The sprayer will activate only when it is turned on.

Typically, if the sprayer on your Delta faucet is leaking, you will first want to check the hose or tube that connects the faucet to the sprayer head. Snap-on hoses are usually the preferred option compared to threaded ones.

There is a possibility that the snap on can loosen up, or that it did not fit correctly at first. In that case, it would be wise to replace the hose and ensure the fit is as snug as possible.

Follow the steps in this guide, and make sure to keep an adjustable wrench and a small bucket with you. When you follow this guide, you will find it easy to remove the sprayer head.

Nonetheless, you must first determine which type of faucet you have.

How to Disconnect Sprayer Hose From Delta Faucet: 5 best steps

Disconnect Sprayer Hose from Delta Faucet

Materials required

  • bucket or bowl (to store water)
  • Adjustable wrench
  • Basin wrench (if needed)

When it comes to a basin wrench, sometimes referred to as a sink wrench, it is a plumbing tool that can unbolt fasteners which are virtually difficult to reach with any other kinds of plug wrenches.

In addition to the long shaft, it has asymmetrical jaws on one end, and a handle on the opposite end.

In addition, it can be used to reach, for example, the tightening nuts that are required to secure faucets to sinks. These nuts are often found in deep recesses within sinks.

The kitchen faucets with sprayer hose by Delta company come in three different types based on the models.

Model 1: This kitchen faucet has one handle with a pullout sprayer attached to it. Its spout is also utilized as a vegetable sprayer.

Model 2: This is a two handle kitchen faucet with a center set. The water faucet, the shut-off valves for hot and cold water, as well as the veggie sprayer, are all placed in a row on the sink.

Model 3: Despite the simplicity of the faucet, it comes with a separate vegetable sprayer that has a single handle.

Follow the steps below depending on the type of delta faucet stem you have.

Step 1: Shut Down the Water Supply

The water supply should be shut off by closing the water valve knobs, pipe etc and use the sprayer to remove all the water that is left in the hose.

Step 2: Disconnecting the Hose

The first thing that needs to be done if you have any of these Delta faucet types is detach the sprayer hose from the faucet outlet tube.

Luckily, this is a snap-on connection, which makes it very easy to connect. The steps are as follows:

Find the outlet tube and reach beneath the counter to locate it. Once it is located, proceed to find the spray hose which is connected to it.

Please check whether the sprayer hose is securely attached to the outlet tube with plastic clips. It is a smart idea to unclip it and place it safely away (since you will need it to reconnect the sprayer hose to your sprayer).

Whenever you disconnect the sprayer hose and the outlet tube, place the bucket in a manner that all remaining water will flow into the bucket.

If you need to disconnect the sprayer hose, press the connection down or pull it from deck fitting.

If the faucet in question is a pull-out type, it will have a weight attached to the sprayer hose. If this is the case, it should be removed.

Step 3: Take off the sprayer head

Lastly, we need to take off the sprayer head. If you have a Delta model 2 or model 3 kitchen faucet, please follow the instructions below.

Rotate the slide nut counterclockwise so that the sprayer head can be removed from the hose.

It is wise to leave the spray head to dry after removing it.

Mineral deposits may form around the sprayer’s internal threads, especially after using it for a while. These can make turning or opening the sprayer difficult.

If you want to overcome this problem, you may mix equal amounts of white vinegar and water in a bottle and soak the head in this mixture.

It will take approximately 30 to 60 minutes for the sprayer head to detach from the hose.

In the case of the pull-out type (Type 1), the sprayer head includes the faucet spout. Please follow the instructions below.

The sprayer must be pulled out somehow.

In order to prevent it from running back down the faucet, you’ll want to make a loop with the sprayer’s hose.

Check the type of connector body that is used to connect the sprayer to the head. The connection can be snapped on/quick release or it can be threaded.

In the case of quick release connections, press the quick release button and remove the sprayer head.

In case the sprayer head is threaded, you will need to use a basin wrench to loosen the head screw and nuts, which allows you to remove it. Make sure the sprayer hose is out of the way.

Step 4: Look for any leaks

Make sure the sprayer head is not corroded and that the hose of the sprayer doesn’t leak. If the sprayer hose has leaking, then this may be the time for the replacement hose.

Change the sprayer hose and install it correctly. you don’t need to worry about installation. It is very simple.

Step 5: Reattach the hose to the fitting

The only thing you need to do is reassemble all of it if there is nothing wrong. Here is the way you do it.

  1. Reconnect the hose to the spray head of the sprayer.
  2. If you are using a type 2 faucet, install the hose into the hole of the sprayer.
  3. For the pullout type of faucet, you will need to place the hose through its neck.
  4. Be sure to place the sprayer heads back to their original positions.
  5. You’ll need to find the outlet tube under the counter so you can handle it.
  6. The sprayer hose should be installed or passed through the weight of the pull-out type.
  7. After that the sprayer hose should be linked to the outlet tube.
  8. Make sure to fix any clips or supplies that the sprayer hose may have come with.
  9. Using a little pressure, ensure that the sprayer hose is securely attached to a free joint.

Step 7: Fix any broken parts

Open up the water supply lines once again. If there are any leaks in the faucet or sprayer, make sure you run them so you can verify if they are leaking.

However, if there are still leaks in Delta hose assembly (it is highly unlikely, unless the mechanism for snapping the assemblies on is not secure), you can use some silicon glue on the leaking area to seal it.

How to Remove Delta Faucet Spray Hose

Watch the video to know how to undo the spray hose from delta faucet!


The above steps outline how to disconnect spray hose from delta faucet. As you can see, the process is an easy one. You should not hesitate to fix your sprayer yourself if it is leaking.

Whenever a leak occurs, it can cause a lot of frustration. If the person understands what the root cause of the problem is, they can definitely do this.

Additionally, you will not have to spend maximum money on the plumber for tub, and you will have the opportunity to learn something that is helpful.

Therefore, I suggest that you head over to your local hardware store and pick up some basic tools to get you started. Be careful not to overpay the plumber for the work.

The faucet can be fixed by yourself in most cases. Fixing it is not only easy, but it is also enjoyable.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top